Graco XM Series Repair Parts Download

Page: 35 / 106

Repair

313289W

7. Remove front display panel (204d) and gasket

(204g).

8. Discard old display assembly.

9. Place new front display panel (204d) and gasket

(204g) on front panel of control box (11).

NOTE:

To ease installation process use clear tape

to hold front display panel in place.

10. Carefully connect display cables and key switch

cable to new circuit board.

11. Install new rear display panel (204c) and secure

with four screws (204b). Ensure key switch cable
protrudes from opening in top of display module.

12. Install access cover and screws. Apply warning

label to access cover.

13. Reconnect CAN cable to display module.

14. Reconnect power.

15. Load software. See

Upgrade Software

, 33.

16. Replace shroud.

17. Configure system settings as they were set on old

display. See your XM sprayer operation manual for
instructions.

Replace Front Panel

See

Replace Display

, page 34, for instructions

Wall Power Supply Control Components

Replace Power Supply Module

1. Remove shroud. See

Remove Shroud

2. Disconnect main power.

3. Remove four nuts (4); leave two nuts on left side of

panel tight. Open front panel of control box (11).

4. Disconnect incoming power cable connections to

power supply module and ground lead (260) from
control box.

5. Disconnect power supply cable (272) from FCM

(218). See

Fluid Control Assembly

on page 40.

6. Remove four screws (273) holding power supply

module (270) bracket in place.

7. Remove and replace power supply module (270).

8. Follow steps in reverse order to install new power

supply module.

204b

204c

204g

204d

Display Cable

239

272

270

260

273

Summary of Contents for XM Series











































































































Search results

Summary of Contents for XM Series

Reviews:

Related manuals for XM Series

Brands by name

Popular brands

Graco XM Series, Repair Parts

Search results

Summary of Contents for XM Series

Reviews:

Related manuals for XM Series

Brands by name

Popular brands