Graco 309028ZAT Instructions Manual Download Page 54

Page: 54 / 98

Troubleshooting

309028ZAT

Air Motor Troubleshooting

For additional information about the air motor, refer to

Related Manuals

on page 3 to find the applicable instruction

manual.

Junction Box Panel Troubleshooting

Problem

Cause

Solution

Air motor will not shift directions,
stalled in DOWN position

Main air valve spool is dirty or
damaged

Clean/rebuild main air valve.

Air motor will not shift directions,
stalled in UP position

Air motor stalled halfway between
the top and bottom

Air continually exhausting around air
motor shaft.

Air motor shaft seal is damaged

Replace air motor shaft seal.

Air continually exhausting around
the air valve/slide valve

Air valve/slide valve gasket is
damaged

Replace the valve gasket.

Air continually exhausting from
muffler while the motor is idle

Internal seal damage

Rebuild air motor.

Oil leaking from exhaust port

Too much lubricant mixed in with the
air supply

Reduce lubricant supply.

Frost build-up on muffler

Air motor operating at high pressure,
or high cycle rate

Reduce pressure, cycle rate, or duty
cycle of the air motor.

Problem

Cause

Solution

Power from PLC control panel is
ON, but no indicator lights are lit at
Junction Box Panel.

The knife switch disconnect contacts
(KS100 and KS102) are open.

Check the PLC power connections
at customer’s site.

One or more fuses blown.

Replace the blown fuse(s). Check
FU136 and FU143 located inside
the knife switch disconnect blocks.

Voltage limit to circuits in Junction
Box Panel was exceeded.

Check the surge suppressors
SUP136 and SUP144. Replace if
required. Reset power to unit.

Summary of Contents for 309028ZAT



































































































Search results

Summary of Contents for 309028ZAT

Reviews:

Related manuals for 309028ZAT

Brands by name

Popular brands

Graco 309028ZAT, Instructions Manual

Search results

Summary of Contents for 309028ZAT

Reviews:

Related manuals for 309028ZAT

Brands by name

Popular brands