Graco 309028ZAT Instructions Manual Download Page 22

Page: 22 / 98

Installation

309028ZAT

Connecting Power to the
Junction Box

Perform the following procedure to connect the power to
the Junction Box Panel (H).

Have a qualified electrician connect the Junction Box
Panel (H) to a grounded electrical source and
disconnect that has the following required service
ratings:

To connect the Junction Box Panel (H) to the electrical
source, perform the following steps:

1. Shut off system power at the main circuit breaker.

2. Remove the cover from the Junction Box Panel (H).

3. Locate the PLC power terminals KS102 and KS100

on the terminal strip inside the Junction Box Panel
(H). See F

. 8. For more information, refer to

Electrical Diagram

on page 91.

4. Using the upper wire duct on the left-hand side of

the Junction Box Panel (H), string two 14 AWG
wires inside the box from the electrical power
source.

5. Connect a ground wire to the ground lug shown in

. 8 on page 23.

6. Connect the two 14 AWG wires to power terminals

KS102 (L1, hot) and KS100 (L2, neutral) in the
Junction Box Panel (H).

7. Seal the area where wires entered the Junction Box

Panel (H).

8. Replace the cover on the Junction Box Panel (H).

All electrical wiring must be done by a qualified
electrician and comply with all local codes and
regulations.

NOTICE

If power and grounding connections are not done prop

erly, the equipment may be damaged and the warranty
will be voided.

Phase

Circuit Breaker

120 Vac Models

50/60

5 Amp

24 Vdc Models

Summary of Contents for 309028ZAT



































































































Search results

Summary of Contents for 309028ZAT

Reviews:

Related manuals for 309028ZAT

Brands by name

Popular brands

Graco 309028ZAT, Instructions Manual

Search results

Summary of Contents for 309028ZAT

Reviews:

Related manuals for 309028ZAT

Brands by name

Popular brands