Graco 309028ZAT Instructions Manual Download Page 53

Page: 53 / 98

Troubleshooting

309028ZAT

Pump Troubleshooting

For additional information about the displacement Pump, refer to

Related Manuals

on page 3 to find the applicable

instruction manual.

Problem

Cause

Solution

Rapid downstroke or upstroke

(pump cavitation)

Air is trapped in Pump.

Bleed air from the Pump using this

procedure:

1. Place a waste container under

the Pump Bleed Port (Q).

2. Press the PRIME PUMP

Pushbutton to turn on air to the
Pump.

3. Allow material to flow from the

Bleed Port until it is air-free.

4. Release the PRIME PUMP

Pushbutton to shut off air to the
Pump. Close the Bleed Port.

5. Turn air on to the Pump and set

the Pump air regulator for normal
operation.

Downstroke: Lower check in Pump
is worn.

Upstroke: Upper check in Pump is
worn.

Rebuild and replace Pump, as
necessary.

Material leaks around Pump outlet

Outlet fitting is loose.

Tighten outlet fitting.

Material leaks around Bleed Port (Q) Bleed Port fitting is loose.

Tighten Bleed Port fitting.

Pump won’t move up or down

Problem with air motor.

See

Air Motor Troubleshooting

chart on page 54.

Foreign object lodged in Pump.

Remove object and rebuild Pump

assembly.

Wet cup leaks

Worn throat packings.

Tighten wet cup. Replace throat
packings.

Summary of Contents for 309028ZAT



































































































Search results

Summary of Contents for 309028ZAT

Reviews:

Related manuals for 309028ZAT

Brands by name

Popular brands

Graco 309028ZAT, Instructions Manual

Search results

Summary of Contents for 309028ZAT

Reviews:

Related manuals for 309028ZAT

Brands by name

Popular brands