Grace Company QuiltMotion Assembly Instructions Manual Download Page 182

Page: 182 / 198

173

Motor Plate (1)

M6 x 20mm

SBHCS (5)

M6 Nut (5)

Motor Plate

Clamp (5)

Step 1b – Motor Plate Installation - Pro Carriage

Parts Needed:

1-2b: Attach the Motor Plate to the Bottom

Carriage using (5) M6 x 20mm SBHCS (5) Motor

Plate Clamps, and (5) M6 Nuts.

Note: Make sure the Motor Plate is centered in the

Carriage.

1-1b: Insert the QuiltMotion Motor Plate into the

Bottom Carriage at an angle.

Note: If Motor Plate will not fit, remove foam.

Tools Needed:

4mm Allen Wrench

10mm & 13mm Box End Wrench

Gracie King/Queen Frame

QuiltMotion

Motor Plate

Bottom Carriage

Front of Carriage

Back of Motor Plate

Front of Carriage

M6 x 20mm SBHCS

M6 Nut

Motor Plate Clamp

Summary of Contents for QuiltMotion







































































































































































































Search results

Summary of Contents for QuiltMotion

Reviews:

Related manuals for QuiltMotion

Brands by name

Popular brands

Grace Company QuiltMotion, Assembly Instructions Manual

Search results

Summary of Contents for QuiltMotion

Reviews:

Related manuals for QuiltMotion

Brands by name

Popular brands