Grace Company QuiltMotion Assembly Instructions Manual Download Page 55

Page: 55 / 198

4-3: Attach the Q-Zone Hoop-Frame QM Belt

Bracket to the Right Frame End using (2) pre-

installed M6 x 16mm Set Screws.

Note: Do not tighten set screws at this time.

4-4: Install the Belt Tensioner to the Q-Zone Hoop-

Frame Belt Bracket using (2) M6 x 10mm Hex Bolts

and (2) M6 Nuts.

4-5: Tilt the Bottom Carriage onto its side.

Q-Zone Hoop-Frame

QuiltMotion

4-6: Keep the Long Belt flat and thread the Long

Belt into the gearbox in the QuiltMotion Motor Plate

from the bottom until it comes out the top of the

Bottom Carriage.

Q-Zone Hoop-Frame QM Belt Bracket

M6 x 16mm Set Screw

Right Frame End

M6 x 10mm Hex Bolt

Belt Tensioner

M6 Nut

Long Belt

Summary of Contents for QuiltMotion







































































































































































































Search results

Summary of Contents for QuiltMotion

Reviews:

Related manuals for QuiltMotion

Brands by name

Popular brands

Grace Company QuiltMotion, Assembly Instructions Manual

Search results

Summary of Contents for QuiltMotion

Reviews:

Related manuals for QuiltMotion

Brands by name

Popular brands