Grace Company QuiltMotion Assembly Instructions Manual Download Page 18

Page: 18 / 198

Tools Needed:

10mm & 13mm Open End Wrench

Step 3c – Short Belt Installation - Top Plate
Parts Needed:

Short Belt (1)

Belt Tensioner (1)

M6 x 20mm

Hex Bolt (2)

Front Belt

Clamp (1)

Back Belt Clamp (1)

M6 x 10mm

Hex Bolt (2)

M6 Nut (4)

Continuum Frame QuiltMotion

3-1c: Place the most curly end of the Short Belt

into the Back Belt Clamp. Place the Front Belt

Clamp over the belt and place (2) M6 x 20mm Hex

Bolts through the Belt Clamp.

3-2c: Assemble the completed assembly (from

Step 3-1b) to the front end of the Top Plate using

(2) M6 Nuts.

Note: The teeth of the belt should be facing

towards the Top Plate.

Short Belt

Back Belt Clamp

M6 x 20mm Hex Bolt

Front Belt Clamp

Belt Clamp Assembly

M6 Nut

Summary of Contents for QuiltMotion







































































































































































































Search results

Summary of Contents for QuiltMotion

Reviews:

Related manuals for QuiltMotion

Brands by name

Popular brands

Grace Company QuiltMotion, Assembly Instructions Manual

Search results

Summary of Contents for QuiltMotion

Reviews:

Related manuals for QuiltMotion

Brands by name

Popular brands