Grace Company QuiltMotion Assembly Instructions Manual Download Page 20

Page: 20 / 198

4-1: Place the most curly end of the Long Belt into

the Back Belt Clamp. Install the Front and Back

Belt Clamps to the Continuum QM Belt Bracket

using (2) M5 x 20mm SBHCS.

4-2: Install the Belt Clamp Assembly onto the Left

Frame Leg.

Note: Belt Clamp Assembly will be adjusted at a

later time.

4-4: Turn the right knob of the Belt Tensioner

counter clockwise and remove the tensioner knobs.

4-3: Secure the Belt Clamp Assembly to the frame

using (2) pre-installed M6 x 16mm Set Screws.

Note: Do not tighten Set Screws at this time.

Continuum Frame QuiltMotion

Continuum QM Belt Bracket

Front Belt Clamp

M5 x 20mm SBHCS

Long Belt

Belt Clamp Assembly

Long Belt

Back Belt Clamp

M6 x 16mm Set Screw

Belt Clamp Assembly

Summary of Contents for QuiltMotion







































































































































































































Search results

Summary of Contents for QuiltMotion

Reviews:

Related manuals for QuiltMotion

Brands by name

Popular brands

Grace Company QuiltMotion, Assembly Instructions Manual

Search results

Summary of Contents for QuiltMotion

Reviews:

Related manuals for QuiltMotion

Brands by name

Popular brands