Grace Company QuiltMotion Assembly Instructions Manual Download Page 168

Page: 168 / 198

159

3-3a: Assemble the Belt Tensioner onto the

opposite end of the Top Belt Bracket on Bracket

Side A using (2) M5 x 10mm SBHCS.

3-4a: Re-Install the Belt Tensioner Knobs.

3-6a: Attach the Top Belt Bracket to the bottom of

the Sewing Machine using (2) M6 x 25mm SBHCS.

Note: Be sure the Belt Tensioner is at the back of

the machine. Slide Top Belt Bracket as far to the

rear as possible.

3-5a: Remove the Thread Stand from your machine.

See your machine manual for instructions.

GMQ Pro & Little Gracie II QuiltMotion

Belt Tensioner

M5 x 10mm SBHCS

Top Belt Bracket

Thread Stand

Top Belt Bracket

Belt Tensioner

M6 x 25mm SBHCS

Bracket Side A

Summary of Contents for QuiltMotion







































































































































































































Search results

Summary of Contents for QuiltMotion

Reviews:

Related manuals for QuiltMotion

Brands by name

Popular brands

Grace Company QuiltMotion, Assembly Instructions Manual

Search results

Summary of Contents for QuiltMotion

Reviews:

Related manuals for QuiltMotion

Brands by name

Popular brands