manualshive.com logo in svg

GPS Prueftechnik Digital Colour Analyzer, User Manual, Page: 17 / 28

Share
Download
GPS Prueftechnik Digital Colour Analyzer User Manual Download Page 17

 

02.11.2018 

 

17 

3.3.4 To perform a measurement and compare several LEDs by using  
 

“Measurement Window” and “Settings Window”. 

3.3.4.1 Measuring and comparing LEDs with differnet light intensities 

 
In order to compare LEDs use the  “Measurement“ window in connection with the “Measurement settings“ 
window (see figure). 
As described in chapter 3.3.3 it is recommended to find out the optimal sensor settings through the main screen first. 
These were taken over by opening the “Measurement settings“ window. During the take over of the exposure time and 
sensor range it is shown, if a sensor is occupied by an offset. In the below-mentioned example five sensors were set via 
the main screen. Thereby sensor three with a non-volatile stored offset is occupied by fixed calibration. 

By opening the “Measurement“ window the colour values for the five set sensors, which have been find out over the main 
screen, appear (see figure). 

Figure 14.5: List of settings 

Figure 14.6:  
List of measurement 

Summary of Contents for Digital Colour Analyzer





























Reviews:

No comments