Gorilla Playsets Riverview 801N User Manual Download Page 99

Page: 99 / 116

STEP 58: ATTACHING THE SAFETY HANDLES

WASHERS.

1: LOCATE TWO SAFETY HANDLES PROVIDED WITH YOUR PLAYSET.

2: LOCATE THE HARDWARE PROVIDED IN THE BAG WITH THE HANDLES.

**DO NOT USE THE SCREWS PROVIDED IN THE BAG WITH THE HANDLES**

3: LOCATE FOUR #14 X 1" LONG PAN HEAD SCREWS IN YOUR MAIN HARDWARE PACKAGE. USE THE 1/4" FLAT

WASHERS PROVIDED IN THE BAG WITH THE HANDLES.

4: PLACE THE HANDLES 1" AWAY FROM THE EDGE OF EACH PANEL SLAT ABOVE THE LADDER AT THE REAR OF THE

PLAY SET. ADJUST THE HANDLES UP OR DOWN TO SUIT THE NEEDS OF YOUR CHILD.

5: ATTACH EACH HANDLE TO THE PANEL SLATS USING TWO #14 X 1" LONG PAN HEAD SCREWS AND TWO 1/4" FLAT

**DO NOT USE THE SCREWS PROVIDED IN THE BAG WITH THE SAFETY HANDLES.**

1/4" FLAT WASHER

SAFETY HANDLE

#14 X 1" LONG PAN

HEAD SCREW

Summary of Contents for Riverview 801N





















































































































Search results

Summary of Contents for Riverview 801N

Reviews:

Gorilla Playsets Riverview 801N, User Manual, Page: 99 / 116

Search results

Summary of Contents for Riverview 801N

Reviews: