manualshive.com logo in svg

Gorilla Playsets Riverview 801N, User Manual, Page: 16 / 116

Share
Download
Gorilla Playsets Riverview 801N User Manual Download Page 16

Counter Sun  Hole

Through Hole

This page is a list of definitions and explanations used throughout our 

instructions to aid you in the assembly of your play set.

Offset Holes

 Throughout the installation procedures  e  ill refer to parts  ith offset 

holes. This refers to the orientation of the holes on the  oard. An offset hole is one that 
is closer to one side than it is the other or in other  ords  it is not centered on the  oard. 
In the procedures you  ill  e instructed to attach the  oards  ith the holes offset up or 

ith the holes offset do n. This refers to  hich side of the  oard the hole/holes should 

e closer to. Offset holes up  hole/holes  ill  e closer to the top of the  oard. Offset 

holes do n  hole/holes  ill  e closer to the  ottom of the  oard. Note: some parts do 
not ha e offset holes   ut instead the holes are on center. Therefore there  ill not  e 
any reference on ho  to offset these parts.

EXAMPLE OF OFFSET HOLES UP

  

EXAMPLE OF OFFSET HOLES DOWN

Counter-sunk holes 

 Many of the parts that  ill  e used ha e counter sun  holes. A 

counter sun  hole is one that surrounds one side of a through hole   ut does not e tend 
through the  ood it s self. When using a counter sun  hole the  olt  ill  e inserted 
through the through hole and either the head of the  olt and  asher or nut and  asher 

ill occupy the counter sun  hole. 

Lag Screws

 Lag scre s are used in the construction of our play sets to enhance 

the structural integrity of the unit. There  ill not  e predrilled holes in the post for lag 
scre  installation. Lag scre s are self tapping  though if you are using a manual soc et 

rench it may  e ad antageous to pre drill a hole  rst. Instructions for this are pro ided 

on a separate page in the front of the manual. Be sure to tighten the lags completely 

hen dri ing them in  y hand. Po er tools such as a hea y duty impact dri er or large 

po er drill should ha e enough tor ue to dri e in the lag scre s   ut ma e sure not to 
o er tighten as this can cause the threads to  strip out  in the post. 

Summary of Contents for Riverview 801N





















































































































Reviews:

No comments