manualshive.com logo in svg

Gorilla Playsets Riverview 801N, User Manual, Page: 51 / 116

Share
Download
Gorilla Playsets Riverview 801N User Manual Download Page 51

                                                  

THE FOLLOWING STEP IS RECOMMENDED TO PREVENT POSSIBLE SPLITS IN THE 

STEP 10: DECK BOARDS

1/8" DRILL BIT AT THE DIMENSIONS SHOWN BELOW.

WOOD.

1: PRE-DRILL THE ENDS OF THE DECK BOARDS TO PREVENT INSTALLATION DAMAGE. PRE-DRILL BOTH ENDS WITH A 

2: START WITH A 5/4 X 6 X 47-1/2" DECK BOARD AT ONE END OF THE FORT. CENTER THE BOARD BETWEEN THE FRONT 

FACE BOARD AND THE REAR BOTTOM PANEL BOARD AND ATTACH IT WITH 2" WOOD SCREWS THROUGH THE 

PREDRILLED HOLES AND INTO THE DECK SUPPORT SHOWN BELOW. LEAVE A UNIFORM ( APPROXIMATELY 1/4") 

SPACE BETWEEN THE DECK BOARDS. NOTE THE TOP OF THE SCREW HEAD SHOULD BE FLUSH TO THE TOP OF THE 

DECK BOARDS.

LAY ALL DECK BOARDS ACROSS THE DECK SUPPORTS BEFORE SECURING THEM TO 

THE FORT. THIS WILL ENSURE THAT YOU HAVE EQUAL SPACING ACROSS THE DECK.

2" WOOD SCREW

5/4 X 6 X 47-1/2"

DECK BOARD

Summary of Contents for Riverview 801N





















































































































Reviews:

No comments