manualshive.com logo in svg

Gorilla Playsets Riverview 801N, User Manual, Page: 44 / 116

Share
Download
Gorilla Playsets Riverview 801N User Manual Download Page 44

                                   

STEP 5: FRONT FRAME ASSEMBLY

1: PLACE THE 2 X 6 X 70" SANDBOX BOARD ON THE FRONT OF THE CORNER POSTS. THE HOLES IN THE SANDBOX 

BOARD SHOULD BE OFFSET UP.

2: USE 5/16 X 4-1/2" HEX BOLTS AND 5/16" WASHERS TO ATTACH THE TOP HOLES OF THE SANDBOX BOARD TO THE T-

NUTS INSTALLED ON THE CORNER POSTS. THE BOTTOM HOLES WILL BE USED LATER.

3: PLACE THE 2 X 6 X 70" FRONT FACE BOARD WITH NOTCHES ON THE FRONT OF THE CORNER POSTS. THE HOLES IN 

THE FRONT FACE BOARD SHOULD BE OFFSET UP.

4: USE 5/16 X 4-1/2" HEX BOLTS AND 5/16" WASHERS TO ATTACH THE TOP HOLES OF THE FRONT FACE BOARD TO THE 

T-NUTS INSTALLED ON THE CORNER POSTS. THE BOTTOM HOLES WILL BE USED LATER.

5: PLACE THE 2 X 6 X 70" TOP PANEL BOARD ON THE FRONT OF THE CORNER POSTS. THE HOLES IN THE TOP PANEL 

BOARD SHOULD BE OFFSET UP.

6: USE 5/16 X 4-1/2" HEX BOLTS AND 5/16" WASHERS TO ATTACH THE TOP HOLES OF THE TOP PANEL BOARD TO THE T-

NUTS INSTALLED ON THE CORNER POSTS.

5/16" WASHER

FRONT OF PLAY SET

HEX BOLT

5/16 X 4-1/2"

LEFT SIDE

OF PLAY SET

2 X 6 X 70" 

SANDBOX BOARD

(OFFSET HOLES UP)

2 X 6 X 70"

FRONT FACE BOARD

(OFFSET HOLES UP)

2 X 6 X 70"

TOP PANEL BOARD

(OFFSET HOLES UP)

Summary of Contents for Riverview 801N





















































































































Reviews:

No comments