manualshive.com logo in svg

Gorilla Playsets Riverview 801N, User Manual, Page: 15 / 116

Share
Download
Gorilla Playsets Riverview 801N User Manual Download Page 15

General Info to Review Before Installation

• Depending on your e perience  assem ly of the playset can ta e as little as   hours 
up to 24 hours  depending on si e  after in entory of parts  therefore   e recommend 

you set aside a full two days for assembly.

• Identify all of the parts for your play set. Empty each  o  and lay out  oards so you 
can see each part. Your instruction  oo   ill ha e detailed dra ings that  ill ma e it 
easy for you to recogni e indi idual parts. Keep all hard are and metal parts separate 
from  ooden pieces.

• After e erything is laid out  chec  carefully to ensure all parts are present. Ma e sure 
there are no  ro en  oards.

• Find an area to sort your hard are. It is  est to open the hard are on a solid surface 
so that you do not lose any pieces in the grass. This  ill sa e time and familiari e you 

ith all the different pieces in the hard are  ag.

• Important note: Wood has some natural defects such as  nots  surface crac s  etc  
We re ect parts that are structurally defecti e. We use a high  uality lum er in our 
structures  ho e er  you should inspect each part for splinters or rough spots and sand 
them smooth to pre ent in ury.

• After familiari ing yourself  ith all of the components  read all instructions thoroughly. 
Reading instructions after you ha e studied the parts  ill help you understand the 
installation process  and help to eliminate unnecessary mista es.

• Pay close attention to the diameter and length of each  olt and scre .

• Ne er tighten hard are completely at  rst. It helps to ha e some ad ustment for  olt 
alignment  hile you are attaching parts together. After e erything is s uare  tighten 
each  oint.

• After the main unit is assem led it is critical that the  oor is le el and s uare. If the 
main frame is not le el  the  alls and  oor  ill  e out of s uare.

• After you complete installation  ma e sure e ery  olt  scre  and nut is tight  and e ery 

oard is secure. Wood  ill e pand and contract  ith the seasons.

• Place the set on le el ground  not less than   feet from any structure or o struction 
such as a fence  garage  house  o erhanging  ranches  laundry lines  or electrical 

wires.

Summary of Contents for Riverview 801N





















































































































Reviews:

No comments