manualshive.com logo in svg

Gorilla Playsets Riverview 801N, User Manual, Page: 84 / 116

Share
Download
Gorilla Playsets Riverview 801N User Manual Download Page 84

MARK DRAWN.  FASTEN THE SMALL RAYS WITH TWO 2" WOOD SCREWS EACH. REPEAT ON OTHER SIDE OF 

FORT. 

1: LOCATE TWO 5/4 X 2 X 23" LARGE RAYS, TWO 5/4 X 2 X 16" SMALL RAYS AND TWO 5/4 X 2 X 18" SMALL RAYS.

2: PRE-DRILL ALL SMALL RAYS AT 3/4" ON CENTER FROM EACH END WITH A 1/8" DRILL BIT. 

PRE-DRILL ALL LARGE RAYS 3/4" ON CENTER FROM THE BOTTOM END WITH A 1/8" DRILL BIT.   PRE-DRILL THE TOP 

END 3/4" FROM THE TOP END AND 1/2" FROM THE SIDE WITH A 1/8" DRILL BIT. (SEE DETAIL A)  THIS IS NECESSARY 

TO AVOID HITTING THE JOINT WHERE THE ROOF SUPPORTS MEET.

3: CENTER THE 5/4 X 2 X 23" LARGE SUNRAY ONTO THE SUN AND THE ROOF SUPPORT BOARDS AND FASTEN 

WITH TWO 2" SCREWS.

4: EQUALLY SPACE THE SMALL RAYS ABOUT THE SUN ( THREE ON EACH SIDE OF LARGE RAY) AND MARK THE 

POSITION OF THE SMALL RAYS WITH A PENCIL.

5: SECURE THE SMALL RAYS ONE AT A TIME TO THE SUN AND THE ROOF SUPPORTS AND LINE THEM UP WITH THE 

STEP 43: SUNBURST

5/4 X 2 X 23"

SMALL RAY

5/4 X 2 X 16"

2" WOOD SCREW

SMALL RAY

LARGE RAY

5/4 X 2 X 18"

ROOF SUPPORTS

SUN

A

DETAIL A 

SCALE 1 : 6

FROM SIDE.

DRILL HOLE 1/2"

3/4"

Summary of Contents for Riverview 801N





















































































































Reviews:

No comments