manualshive.com logo in svg

Gorilla Playsets 1500CWR, Manual, Page: 79 / 119

Share
Download
Gorilla Playsets 1500CWR Manual Download Page 79

STEP 32:  ROOF FRONT SECTION

1: PLACE THE 1 X 4 X 76-7/8" ROOF STARTER FRONT BOARD AT THE PEAK OF THE ROOF OVERLAPPING THE ROOF

STARTER REAR. THE HOLES IN THE ROOF STARTER FRONT SHOULD BE CENTERED ON THE ROOF SUPPORTS, AND THE

FLAT TOP END OF THE ROOF STARTER FRONT SHOULD BE PLACED FLUSH TO THE TOP EDGE OF THE ROOF

STARTER REAR.

2: FASTEN THE ROOF STARTER FRONT TO THE ROOF SUPPORTS WITH 1-1/2" WOOD SCREWS.

3: PLACE THE 1 X 5 X 76-7/8" ROOF BOARDS ON TOP OF THE ROOF SUPPORTS, FITTING THE TONGUE END INTO THE

GROOVE END OF THE ROOF STARTER REAR. THIS SIDE OF THE ROOF GETS SEVEN ROOF BOARDS.

4: FASTEN THE ROOF BOARDS TO THE ROOF SUPPORTS WITH 1-1/2" WOOD SCREWS.

1-1/2" WOOD 

SCREW

1 X 4 X 76-7/8"

ROOF STARTER FRONT

ROOF BOARDS

(FIRST ONE)

ROOF BOARDS

(SEVENTH ONE)

OVERLAP

FLAT TOP END

FLUSH TO TOP EDGE

1 X 4 X 76-7/8"

ROOF STARTER FRONT

(4" WIDE)

1 X 3 X 76-7/8"

ROOF STARTER REAR

(3-1/4" WIDE)

Summary of Contents for 1500CWR
























































































































Reviews:

No comments