Gorilla Playsets 1500CWR Manual Download Page 78

Page: 78 / 119

5/16"

WASHER

1 X 4 X 76-7/8"

(FIRST ONE)

LAG SCREW

ROOF FINISHER

1-1/2" WOOD SCREW

ROOF STARTER REAR

ROOF BOARD

(SEVENTH ONE)

ROOF BOARD

5/16" X 3-1/2"

CHIMNEY

2 X 4 X 69-3/4"

ROOF FINISHER

SUPPORT

STEP 31: ROOF REAR SECTION AND CHIMNEY

1: PLACE THE 1 X 5 X 76-7/8" ROOF BOARDS ON TOP OF THE ROOF SUPPORTS, FITTING THE TONGUE END INTO THE

GROOVE END OF THE ROOF STARTER REAR. THIS SIDE OF THE ROOF GETS SEVEN ROOF BOARDS.

2: FASTEN THE ROOF BOARDS TO THE ROOF SUPPORTS WITH 1-1/2" WOOD SCREWS.

3: PLACE THE 1 X 4 X 76-7/8" ROOF FINISHER AT THE END OF THE ROOF ASSEMBLY, AND FASTEN WITH 1-1/2"

WOOD SCREWS.

4: MOUNT THE 2 X 4 X 69-3/4" ROOF FINISHER SUPPORT UNDERNEATH THE ROOF UP AGAINST THE ROOF FINISHER

REAR

AND ATTACH TO THE REAR CORNER POST USING 5/16" LAG SCREWS AND 5/16" WASHERS.

TIP: USE THE INSTRUCTIONS PROVIDED IN THE APPENDIX TO BUILD THE CHIMNEY. INSTALL THREE ROOF BOARDS

AND INSTALL THE CHIMNEY ACCORDING TO THE CHIMNEY INSTRUCTIONS.

Summary of Contents for 1500CWR
























































































































Search results

Summary of Contents for 1500CWR

Reviews:

Gorilla Playsets 1500CWR, Manual, Page: 78 / 119

Search results

Summary of Contents for 1500CWR

Reviews: