manualshive.com logo in svg

Gorilla Playsets 1500CWR, Manual, Page: 49 / 119

Share
Download
Gorilla Playsets 1500CWR Manual Download Page 49

STEP 6: REAR FRAME ASSEMBLY

1: PLACE THE 2 X 6 X 70" SANDBOX BOARD ON THE REAR OF THE CORNER POSTS. THE HOLES IN THE SANDBOX 

BOARD MUST BE OFFSET UP.

2: USE 5/16 X 4-1/2" HEX BOLTS AND 5/16" WASHERS TO ATTACH THE TOP HOLES OF THE SANDBOX BOARD TO THE

T-NUTS INSTALLED ON THE CORNER POSTS. THE BOTTOM HOLES WILL BE USED LATER.

3: PLACE THE 2 X 6 X 70" REAR FACE BOARD ON THE REAR OF THE CORNER POSTS. THE HOLES IN THE REAR FACE 

BOARD MUST BE OFFSET UP.

4: USE 5/16 X 4-1/2" HEX BOLTS AND 5/16" WASHERS TO ATTACH THE TOP HOLES OF THE REAR FACE BOARD TO THE 

T-NUTS INSTALLED ON THE CORNER POSTS. THE BOTTOM HOLES WILL BE USED LATER.

5: PLACE THE 2 X 4 X 70" REAR TOP PANEL BOARD ON THE REAR OF THE CORNER POSTS. THE HOLES IN THE REAR

TOP PANEL BOARD MUST BE OFFSET UP.

6: USE 5/16 X 4-1/2" HEX BOLTS AND 5/16" WASHERS TO ATTACH THE TOP HOLES OF THE REAR TOP PANEL BOARD TO

THE T-NUTS INSTALLED ON THE CORNER POSTS.

REAR FACE BOARD

(OFFSET UP)

(OFFSET UP)

5/16" WASHER

SANDBOX BOARD

2 X 4 X 70"

REAR TOP PANEL BOARD

(OFFSET UP)

2 X 6 X 70"

2 X 6 X 70"

5/16 X 4-1/2"

HEX BOLT

Summary of Contents for 1500CWR
























































































































Reviews:

No comments