Gorilla Playsets 1500AWCR Manual Download Page 72

Page: 72 / 136

STEP 5: FRONT FRAME ASSEMBLY

1: PLACE THE 2 X 6 X 70" SANDBOX BOARD ON THE FRONT OF THE CORNER POSTS. THE HOLES IN THE SANDBOX

BOARD SHOULD BE OFFSET UP.

2: USE 5/16 X 4-1/2" HEX BOLTS AND 5/16" WASHERS TO ATTACH THE TOP HOLES OF THE SANDBOX BOARD TO THE

T-NUTS INSTALLED ON THE CORNER POSTS. THE BOTTOM HOLES WILL BE USED LATER.

3: PLACE THE 2 X 6 X 70" FRONT FACE BOARD WITH NOTCHES ON THE FRONT OF THE CORNER POSTS. THE HOLES IN

THE FRONT FACE BOARD SHOULD BE OFFSET UP.

4: USE 5/16 X 4-1/2" HEX BOLTS AND 5/16" WASHERS TO ATTACH THE TOP HOLES OF THE FRONT FACE BOARD TO

THE T-NUTS INSTALLED ON THE CORNER POSTS. THE BOTTOM HOLES WILL BE USED LATER.

5: PLACE THE 2 X 6 X 70" TOP PANEL BOARD ON THE FRONT OF THE CORNER POSTS. THE HOLES IN THE TOP PANEL

BOARD SHOULD BE OFFSET UP.

6: USE 5/16 X 4-1/2" HEX BOLTS AND 5/16" WASHERS TO ATTACH THE TOP HOLES OF THE TOP PANEL BOARD TO

THE T-NUTS INSTALLED ON THE CORNER POSTS.

HEX BOLT

SANDBOX BOARD

5/16" WASHER

OFFSET HOLES

BOARD

TOP PANEL

2 X 6 X 70"

OFFSET HOLES

BOARD

OFFSET HOLES UP

2 X 6 X 70"

FRONT FACE

2 X 6 X 70"

5/16 X 4-1/2"

FRONT OF FORT

Summary of Contents for 1500AWCR









































































































































Search results

Summary of Contents for 1500AWCR

Reviews:

Related manuals for 1500AWCR

Brands by name

Popular brands

Gorilla Playsets 1500AWCR, Manual

Search results

Summary of Contents for 1500AWCR

Reviews:

Related manuals for 1500AWCR

Brands by name

Popular brands