Gorilla Playsets 1500AWCR Manual Download Page 114

Page: 114 / 136

STEP 44: PICNIC TABLE

1: MEASURE UP 26-3/8" FROM THE BOTTOM OF THE CORNER POSTS ON THE RIGHT SIDE OF THE PLAYSET. MAKE

MARKS ON THE INSIDE OF THE CORNER POSTS WITH A PEN OR PENCIL AT 26-3/8".

2: PLACE THE TOP OF THE RIGHT SIDE ASSEMBLY FLUSH TO THE MARK ON THE RIGHT FRONT CORNER POST. ATTACH

THE RIGHT SIDE ASSEMBLY TO THE INSIDE OF THE CORNER POST WITH #8 X 3" WOOD SCREWS.

3: PLACE THE TOP OF THE LEFT SIDE ASSEMBLY FLUSH TO THE MARK ON THE RIGHT REAR CORNER POST. ATTACH THE

LEFT SIDE ASSEMBLY TO THE INSIDE OF THE CORNER POST WITH #8 X 3" WOOD SCREWS.

(LEG ON INSIDE)

LEFT SIDE ASSEMBLY

(LEG ON INSIDE)

RIGHT SIDE ASSEMBLY

#8 X 3"

WOOD SCREW

NOTE: ROCK WALL AND LADDER

REMOVED FOR CLARITY.

26-3/8"

Summary of Contents for 1500AWCR









































































































































Search results

Summary of Contents for 1500AWCR

Reviews:

Related manuals for 1500AWCR

Brands by name

Popular brands

Gorilla Playsets 1500AWCR, Manual

Search results

Summary of Contents for 1500AWCR

Reviews:

Related manuals for 1500AWCR

Brands by name

Popular brands