Gorilla Playsets 1500AWCR Manual Download Page 105

Page: 105 / 136

EQUAL

ROOF OVERHANG

SLIDE LEF

T OR RIGH

(TEST FIT ONLY)

1 X 4 X 29.29" ROOF

TOP PANEL BOARD

EMPTY

FINISHER LEFT

GABLE ASSEMBLY

FINISHER RIGHT

(TEST FIT ONLY)

EMPTY

1 X 4 X 29.29" ROOF

ROOF

OVERHANG

EQUAL

1-1/2"

WOOD SCREW

33-7/8"

6 78 "

3: AFTER THE GABLE ASSEMBLY IS IN ITS FINAL

POSITION. GO INSIDE ON TOP OF THE DECK AND

PULL THE GABLE ASSEMBLY TOWARDS YOU

MAKING SURE IT IS FLUSH TO THE OUTSIDE OF THE

ROOF AND INSERT TWO 1-1/2" WOOD SCREW

FROM UNDERNEATH THE ROOF INTO THE

GABLE ASSEMBLY ROOF PEAK. USE THE

DIMENSIONS SHOWN IN THE DIAGRAM TO THE

LEFT TO INSERT THE WOOD SCREWS IN THE

CORRECT LOCATION. REMOVE THE ROOF

FINISHERS, THESE WILL BE USED IN A LATER STEP.

NOTE:

CORNER POST

REMOVED FOR

CLARITY

STEP 35: ATTACHING THE FRONT GABLE

PULL TOWARDS

YOU

1: MOUNT THE GABLE ASSEMBLY RESTING ABOVE THE TOP PANEL BOARD, MAKE SURE THE GABLE ASSEMBLY IS FLUSH

AGAINST THE FRONT CORNER POSTS. THE GABLE ROOF PEAK SHOULD BE RESTING ON TOP OF THE ROOF FRONT

SECTION.

TIP: MAKE SURE THE DISTANCE BETWEEN THE GABLE ASSEMBLY AND THE ROOF OVERHANG IS EQUAL ON BOTH SIDES.

IT IS RECOMMENDED TO TEST FIT THE 1 X 4 X 29.29" ROOF FINISHERS FRONT LEFT AND RIGHT TO ASSURE THIS EQUAL

DISTANCE (DO NOT FASTEN). IF NECESSARY SLIDE THE GABLE ASSEMBLY LEFT OR RIGHT UNTIL FINAL POSITION IS

ACCOMPLISHED.

2: THE GABLE ASSEMBLY BOTTOM COUNTERSUNK HOLES WILL REMAIN EMPTY FOR NOW.

Summary of Contents for 1500AWCR









































































































































Search results

Summary of Contents for 1500AWCR

Reviews:

Related manuals for 1500AWCR

Brands by name

Popular brands

Gorilla Playsets 1500AWCR, Manual

Search results

Summary of Contents for 1500AWCR

Reviews:

Related manuals for 1500AWCR

Brands by name

Popular brands