Gorilla Playsets 1500AWCR Manual Download Page 77

Page: 77 / 136

! ATTENTION !

IN THE FOLLOWING THREE STEPS YOU WILL BEGIN THE INSTALLATION OF THE DECK SPACERS

AND DECK BOARDS. IF YOU HAVE DIFFICULTY GETTING THE DECK BOARDS/DECK SPACERS TO

FIT BETWEEN THE FRONT FACE BOARD AND BOTTOM PANEL BOARD DO THE FOLLOWING:

1: LOOSEN UP THE BOARDS ON THE LEFT AND RIGHT SIDES OF THE PLAY SET. REMOVE THE

SCREWS ON ONE SIDE OF EACH DECK SPACER.

2: ALLOW THE DECK BOARDS TO DROP DOWN IN BETWEEN THE FRONT FACE BOARD AND

BOTTOM PANEL BOARD.

3: TIGHTEN UP THE BOARDS ON THE LEFT AND RIGHT SIDES OF THE PLAY SET.

4: RE-INSTALL THE SCREWS IN THE DECK SPACERS. THEN INSTALL THE DECK BOARDS AS

INDICATED IN THE INSTRUCTIONS.

LEFT SIDE BOARDS

RIGHT SIDE BOARDS

BOTTOM PANEL BOARD

FRONT FACE BOARD

Summary of Contents for 1500AWCR









































































































































Search results

Summary of Contents for 1500AWCR

Reviews:

Related manuals for 1500AWCR

Brands by name

Popular brands

Gorilla Playsets 1500AWCR, Manual

Search results

Summary of Contents for 1500AWCR

Reviews:

Related manuals for 1500AWCR

Brands by name

Popular brands