background image

Page 11

Operating Instructions

Before ‘Starting’ the mixer: 

Always change speeds BEFORE Starting the Mixer!  Failure 

to do so may damage the gears or other parts and WILL void the warranty!

USING THE MIXER’S DIGITAL CONTROLS AND TIMER

SP62P and SP80PL mixer owners only: read through this section and continue to page 13 for further 

operating instructions for use of the digital controls on your mixer.

The mixer is equipped with a digital timer display, minutes and seconds buttons (to adjust the timed operations) 

and Start / Stop buttons. The mixer can function in either timed operation or untimed operation.

Untimed Operation:

  For simple on/off mixing operation in a untimed operating mode, verify that the bowl guard 

and bowl lift are closed and locked into position. 

 

- The display should read 00:00 to operate in untimed mode. Pressing the ‘Stop’ button twice within one  

 

  second will reset the timer back to zero. 

 

- Press the ‘Start’ button to begin mixing. The display will scroll zeros across the display from left to right while 

 

  mixing. Press the ‘Stop’ button once the desired mixing is complete.

Timed Operation:  

The timer on the mixer can be set from 5 seconds to 60 minutes. 

 

1.   Set desired time. Minutes advance by one and seconds advance by fives before rolling over to zero.

NOTE: Press and continuously hold the up arrow buttons to the desired minutes and seconds. Press and 

continuously hold of the button scrolls through the number cycles quickly. (To slow down the selection and to better 

control the setting time, press the up or down arrow button (Do not continuously hold the button down).

 

2.   Once the desired time is set, verify that the bowl guard and bowl lift are closed and locked into position,  

 

 

and then press ‘Start’.

 

3.   Wait for the timed cycle to end or press ‘Stop’ to pause the mixing cycle.

 

 

  

- Pressing the ‘Stop’ button once stops the mixer and pauses the timer during operation.

 

 

 

- Pressing the ‘Stop’ button once while the mixer is not in operation will reset the timer to the  

 

 

 

   last programed/set time.

 

 

 

- Double clicking the ‘Stop’ button twice within one second while the mixer is not in operation  

 

 

 

   will resets the timer back to zero (00:00).

NOTE: If a cycle is interrupted by the bowl guard being opened or by lowering the bowl lift lever, the mixer will 

stop. As soon as the fault is corrected, the “Start” button can be pressed to continue the programmed time.

To add additional minutes or seconds to a mix time, “Stop” the mixer, and adjust the cycle mixing time.

 

4.  Once a timed cycle ends, the mixer will beep for 5 seconds and the digital display will flash for two 

 

 

 

minutes if not reset indicating the timed cycle is complete.

Summary of Contents for SP10





















Reviews: