Glamox B29004003, Manual

Page: 9 / 15

9
Addressable <LMS MG PIR CLS SENSOR-R LONG>
Setting the teach-in function via button
† †
Press the button for > 15 s
▻ The currently measured brightness value is adopted as
the brightness setpoint value.
L
The teach-in function via the button can be disabled using
the app in combination the app remote control when the
"Configuration button/RC" parameter is set to "disabled".
Parameters via remote control
The following parameters can be checked or changed via
the remote control for support during start-up as well as
servicing:
Parameter Description Can be
checked by
app
Can be
changed by
app
Function C1/C2
Selection: switching/
control
x x
Terminal S1 assign-
ment, terminal S2
assignment
Selection: C1/C2/C1+C2 x
Brightness setpoint
value C1, C2
Value range in lux/mea-
surement off
x x
Brightness actual
value C1, C2
Check brightness actual
value
x
Room correction
factor C1, C2
Room correction factor x x
Brightness measure-
ment value C1, C2
Lux meter brightness
value in lux
x
Detection sensitivity
(PIR)
Value range in increments x x
Lighting time delay
Value range in seconds/
minutes
x
Short-term presence Short-term presence: ON/
OFF
x x
Energy saving mode Selection: eco/eco plus x x
Presence switch-on
delay
Value range in seconds/
minutes
x
Presence time delay Value range in seconds/
minutes
x
Switch on dimming
value C1, C2
Value range in % x
Configuration type
C1/C2
Selection: Auto/Man x x
Control speed
Selection: standard/
average/fast
x
Minimum dimming
value
Value range in % x
Maximum dimming
value
Value range in % x
Switch off
brightness
Value range in minutes/
hours/never off
x
Staircase light
function
Selection: ON/OFF x x
Dimming speed:
man. dimming
Selection: standard/fast x
Response after man.
dimming
Selection: school/office x
Standby time
Value range in seconds/
minutes
Permanently on
x
Standby dimming
value
Value range in % x
Parameter Description Can be
checked by
app
Can be
changed by
app
IR group address
C1, C2
Selection: all/I/II/III (app
to VIII)
x
Scene 1 C1,
scene 2 C1
Scene for lighting channel
C1 value range in %
x
Scene 1 C2,
scene 2 C2
Scene for lighting channel
C2 value range in %
x
Configuration
button/RC
Selection: Enabled/
Disabled
x
LED motion display OFF/ON x
Checking the set values:
With the with the app in combination the app remote control,
parameters can be checked by gradually sending the values
to the detector. If the sent value is below the set parameter,
the LED lights up briefly. If the sent value is equal to or above
the set parameter, the LED lights flickers for 2 s.
Function C1, C2
Lighting channels C1 and C2 can be operated together in
switching mode or in the constant light control function. The
function is set via the <Function C1, C2> parameter.
Value range (Glamox Sensor-app)
Switching Lighting channels C1 and C2 are in the switching mode
function
Control Lighting channels C1 and C2 are in the constant light control
function
Terminal S1 assignment, terminal S2 assignment
Terminals S1 and S2 for the buttons can be assigned to the
required lighting channel at any time without rewiring.
Value range (Glamox Sensor-app)
Parameter Lighting channel
Terminal S1
assignment
C1 C2 C1+C2
Terminal S2
assignment
C1 C2 C1+C2
Brightness setpoint value C1, C2
The brightness setpoint value defines the minimum required
brightness. The current brightness is measured below the
presence detector. If the brightness is below the setpoint
value and presence is detected, the light is switched on (for
the fully automatic device configuration type).
A separate brightness setpoint value is available for each
lighting channel C1, C2.