background image

14

LED display motion

Motion detection can be displayed using the LED.

Value range (Glamox Sensor-app)

No display of motion detection.

OFF

The LED is switched on when motion is detected, otherwise it 

remains off.

ON

Presence test

The presence test mode checks the presence detection and 

wiring. The presence test mode can be activated with the app 

in combination with the app remote control. When the test 

mode is set, the detector switches directly to test mode:

 

Every movement is indicated by the LED.

 

The lighting is switched on where there is movement.

 

If there is no movement, the lighting is switched off after 
10 s.

 

The brightness measurement is deactivated, the detector 
does not respond to brightness.

 

Constant light control is deactivated (switching mode).

 

The standby function is deactivated.

 

The detector responds as in the "fully automatic device" 

configuration type – even if "semi-automatic device" is 

set.

 

Teach-in cannot be activated in test mode.

 

The test mode ends after 10 min. The detector restarts 
(see "Switch-on response").

Light test

The light test mode checks the brightness threshold and  

the constant light control. The light test mode can be activa-

ted with the app in combination with the app remote control. 

When the test mode is set, the detector switches directly to 

test mode:

 

The LED shows the light test mode (5 seconds ON, 0.3 
seconds OFF).

 

The presence detector responds as in the normal 
operating mode; it only responds faster to brightness/
darkness.

 

To simulate the response, either actuate the blinds or 
illuminate the area under the presence detector.

 

The test mode ends after 10 min. The detector restarts 
(see "Switch-on response").

 

L

Note: Do not use a torch to trigger the presence detector 
to switch! The adaptive light switching thresholds are 

falsified!

Resetting the DALI EBs/DALI relays

The connected DALI EBs/DALI relays are reset to the factory 

settings.

9.  Technical data

Operating voltage

110–230 V AC, +10 %/–15 %

Frequency

50–60 Hz

Upstream protection device:

16 A

Power consumption (without DALI EB)

< 0.4 W

Type of installation

Ceiling installation; flush/

surface mounted or ceiling 

installation

Recommended installation height

2.0–6.0 m

Minimum height

> 1.7 m

Detection area 

horizontal 360°

Maximum range

20 x 5 m (IH 3.5 m)/100 m

2

 

moving radially

30 x 5 m (IH 3.5 m)/150 m

2

 

moving tangentially

Setting range of brightness setpoint 

value

10–3000 lux

Lighting time delay

10 s–60 min

Presence switch-on delay

0 s–10 min

Presence time delay

10 s–120 min

Lighting standby time

0 s–60 min/permanently on

Standby dimming value

1–25 %

Lighting control output

DALI interface 100 mA, max. 50 

DALI devices, base insulation

Connection type

Screw terminals

Max. cable cross-section

max. 2 x 2.5 mm²

Flush-mounted box size

Size 1, Ø 55 mm (NIS, PMI)

Protection rating

IP 54 when installed

Ambient temperature

–15 °C … 50 °C

CE Declaration of Conformity

This device conforms to the 

safety regulations of the EMC 

Directive 2014/30/EU and of 

Directive 2014/35/EU. 

Troubleshooting

Fault

Cause

Light does not switch 

on or off if presence 

is detected and in 

darkness

Brightness setpoint value is set too low; detector 

is set to semi-automatic device; light was switched 

off manually using buttons or the LMS MG PRO-

GRAM REMOTE BT/LMS MG USER REMOTE; person 

is not in the detection area; obstacle(s) disrupt 

detection; time delay is too short

Light stays on with 

detection of presence 

despite sufficient 

brightness 

Brightness setpoint value is set too high; the light 

was switched on manually a short while ago using 

buttons or the LMS MG PROGRAM REMOTE BT/

LMS MG USER REMOTE (wait 30 min during swit-

ching mode); detector is in test mode

Light does not switch 

off, or light switches on 

spontaneously when 

no one is present 

Wait for time delay (self-learning); 

thermal sources of interference in detection area; 

fan heaters, light bulb/halogen spotlight, moving 

objects (e.g. curtains in front of open windows)

Button does not work

Device still in the start-up phase; illuminated 

button was used without neutral conductor;  

button not connected to master. 

Light cannot be 

switched off with the 

button

Button is not connected to the detector. Check the 

button wiring.

Lighting does not 

respond

Short circuit or interruption on DALI bus. Overvol-

tage on DALI bus: disconnect the detector from the 

mains for 1 minute (thermal fuse).

Error flashing 

 

(4 x per second)

Error in self-test; 

device not functional!

LED is switched on and 

flashes 2 x OFF briefly 

every 3 s

The detector has not detected any DALI EBs. Check 

DALI connections. At least 1 DALI EB must be con-

nected to the detector. Short circuit on DALI bus.

Master/slave, master/

master parallel swit-

ching is not working

The detector and button are not connected to the 

same external conductor. 

Summary of Contents for B29004003
















Reviews: