background image

4

 

All connected buttons are active. Switching on and off as 
well as dimming are possible.

 

Time delay: 10 min.

Configuring the lighting groups with

 

LMS MG PROGRAM REMOTE BT/Glamox Sensor-app

 

Buttons or LMS MG USER REMOTE

Configuring the lighting groups with the LMS MG PROGRAM 

REMOTE BT/App

†

†

Connect the LMS MG PROGRAM REMOTE BT with the corre-

sponding Glamox Sensor-app.

†

†

Place the LMS MG PROGRAM REMOTE BT under the detec-

tor (direct the remote control towards the detector).

†

†

Select LMS MG PIR CLS SENSOR-R LONG as the type in the 

app.

†

†

In the "DALI configuration" menu, select the required group 

assignment.

For the DALI configuration, there are 3 options available:

†

y

"Group assignment (unaddress.)": only DALI EBs without a 

group address are processed.

†

y

"Group assignment (all)": all connected DALI EBs are con-

figured. 

NOTE

: All existing group assignments with group 

number 1 or 2 are deleted.

†

y

"Change group assignment": the next existing EB is 

searched for and selected.

 

After selecting the required group assignment, the 
detector is in the programming mode.

 

A DALI light starts to pulse (random order).

†

†

Use   to assign the required C1 or C2 channel to the DALI 

EB. 

 

▻ As confirmation, the light dims to 20%. 

 

The next DALI light starts to pulse. One after the other, 
the lighting groups are assigned to all the lights. 

 

For group assignment (unaddress.) or (all): if all DALI EBs 
are assigned to a lighting group, the detector terminates 

the configuration process and restarts (startup phase of 

30 s). The detector then switches to the normal opera-

ting mode and the configuration is completed.

 

L

If necessary, the configuration process can be ended by 

pressing „End“ (left function button). 

 

In this case, the system is not ready for operation.

 

If „Change group assignment“ has been selected, use the 
right „>“ button to switch to the next DALI EB without 
changing the lighting group.

†

†

When all required changes have been made, end the confi

-

guration process by pressing „End“ (left function button).

Configuring the lighting groups using buttons

†

†

Set the <Configuration button/RC> parameter to "Enabled". 

All connected buttons can be used for the configuration.

†

†

Press any button 5 times briefly (< 0.4 s) and press and 

hold once (> 15 s).

 

The LED is switched off.

 

A DALI light starts to pulse (random order).

 

The lighting group is assigned by pressing the approp-
riate button:

†

y

1 x short button press = channel C1

†

y

2 x short button press = channel C2 

 

▻ As confirmation, the light dims to 20 % (3 s after the 

last button press). 

 

The next DALI light starts to pulse. One after the other, 
the lighting groups are assigned to all the lights. 

 

If all DALI EBs are assigned to a lighting group, the 

detector terminates the configuration process and 

restarts (startup phase of 30 s). 

 

The detector switches to the normal operating mode 

and the configuration is completed.

 

L

If required, the configuration process can be ended by 

pressing and holding any button for longer than 15 s.  
The detector restarts. 

 

In this case, the system is not ready for operation.

 

L

Instead of using the button, the configuration can also 

be carried out with the ON/OFF buttons on the LMS MG 
PROGRAM REMOTE BT/LMS MG USER REMOTE.

Checking the configuration

The assignment of the lighting groups can be checked by 

switching the individual lighting groups on or off using but-

tons, the LMS MG PROGRAM REMOTE BT/App (for the app, 

select the "Control commands" menu).

 

L

Changing the lighting group for DALI EBs: use the LMS MG 

PROGRAM REMOTE BT/App to change the DALI configura

-

tion via the "Change group assignment" command. 

 

L

With the button: the whole DALI configuration must be 

re-executed.

Switch-on response (configured system)

If voltage is applied, the presence detector goes through two 

phases which are indicated by the LED:

1. Start-up phase (30 s)

 

The red LED flashes in one-second intervals; the lighting 

is switched on with the switch on dimming value.

 

The detector does not react to button commands or 
to the LMS MG PROGRAM REMOTE BT/LMS MG USER 
REMOTE.

 

If absent, the lighting is switched off after 30 s.

2. Operation

 

The red LED is off. The constant light control or switching 
mode are started.

 

The detector is ready for operation.

7.  Functions

Z1

Z2

 Mixed light measurement 

 Presence detection

 Artificial light

 Button for manual lighting control

 Incident daylight

Summary of Contents for B29004003
















Reviews: