Glamox B29004003, Manual

Page: 6 / 15

6
Broadcast <LMS MG PIR CLS SENSOR-R LONG BC>
Teach-in via button
† †
Press the button for > 15 s
▻ The currently measured brightness value is adopted as
the brightness setpoint value.
L
The teach-in function via the button can be disabled using
the app remote control when the "Configuration button/
RC" parameter is set to "disabled".
Parameters via remote control
The following parameters can be checked or changed via
the remote control for support during start-up as well as
servicing:
Parameter Description Can be
checked via
app
Can be
changed via
app
Detection zone Selection: Z1/Z2/Z1+Z2 x x
Function C1
Selection: switching/
control
x x
Brightness set-
point value C1
Value range in lux/measu-
rement off
x x
Brightness actual
value C1
Check brightness actual
value
x
Room correction
factor C1
Room correction factor x x
Brightness
measurement
value C1
Lux meter brightness value
in lux
x
Detection sensi-
tivity (PIR)
Value range in increments x x
Lighting time
delay
Value range in seconds/
minutes
x
Short-term
presence
Short-term presence: ON/
OFF
x x
Energy saving
mode
Selection: eco/eco plus x x
Presence switch-
on delay
Value range in seconds/
minutes
x
Presence time
delay
Value range in seconds/
minutes
x
Switch on dim-
ming value C1
Value range in % x
Configuration
type C1
Selection: Auto/Man x x
Control speed
Selection: standard/
average/fast
x
Minimum dim-
ming value
Value range in % x
Maximum dim-
ming value
Value range in % x
Switch off
brightness
Value range in minutes/
hours/never off
x
Staircase light
function
Selection: ON/OFF x x
Dimming speed:
man. dimming
Selection: standard/fast x
Response after
man. dimming
Selection: school/office x
Standby time
Value range in seconds/
minutes/Permanently on
x
Standby dimming
value
Value range in % x
Parameter Description Can be
checked via
app
Can be
changed via
app
IR group address
C1
Selection: all/I/II/III (app
to VIII)
x
Scene 1 C1 Value range in % x
Scene 2 C1 Value range in % x
Configuration
button/RC
Selection: Enabled/
Disabled
x
LED motion
display
OFF/ON x
Checking the set values:
With the app and the app remote control, parameters can be
checked by gradually sending the values to the detector. If
the sent value is below the set parameter, the LED lights up
briefly. If the sent value is equal to or above the set parameter,
the LED lights flickers for 2 s.
Detection zone
The detection area is divided into two independent detec-
tion zones (see 4. Installation, detection area). For a maxi-
mum range, zone 1 and zone 2 are activated. If a limitation
of the detection area is required, zone 1 or zone 2 can be
deactivated.
Value range (Glamox Sensor-app)
Selection of detection area Z1, Z2, Z1 and Z2
Function C1
The lighting channel C1 can be operated in switching mode or
in the constant light control function. The function is set via
the <Function C1> parameter.
Value range (Glamox Sensor-app)
Switching Lighting channel C1 is in the switching mode function
Control Lighting channel C1 is in the constant light control function
Brightness setpoint value C1
The brightness setpoint value defines the minimum required
brightness. The current brightness is measured below the
presence detector. If the brightness is below the setpoint
value and presence is detected, the light is switched on (for
the fully automatic device configuration type).
Value range (app)
Brightness setpoint value min. 10–3000 lux
Deactivation of brightness measurement (brightness
measurement has no effect)
The lighting channels only switch according to presence
and absence.
Measurement off
Brightness actual value C1
The brightness actual value can be checked for monitoring
purposes. To check, see the "Parameters via remote control"
table.