background image

7

Room correction factor C1, brightness measurement 

value C1

The room correction factor is a measure of the different 

brightness measurements at the ceiling and on the work 

surface (the brightness value depends on the ambient 

conditions).

2,5 m

2,5 m

Z1

Z2

theSenda B 

oder Luxmeter

LMS MG PROGRAM REMOTE BT

or lux meter

Room correction factor = Brightness value at the ceiling

 

 

Brightness value on the floor

The brightness measurement value at the ceiling is influenced 

by the installation location, incidence of light, position of the 

sun, weather conditions, the reflection properties of the room, 

and the furniture. In order to be able to adhere to the requi-

red lux value in the desired area, a comparison of the bright-

ness measurements is necessary.

The measured lux meter value 

 below the presence detector 

is sent to the detector via the remote control.

When sending the brightness measurement value, the room 

correction factor of the corresponding lighting channel is 

automatically adjusted to the conditions inside the room.

Two different procedures can be selected in the app for the 

comparison (automatic/manual calibration).

†

†

Connect the app remote control LMS MG PROGRAM 

REMOTE BT with the corresponding Glamox Sensor-app.

†

†

Select the appropriate detector type <LMS MG PIR CLS 

SENSOR-R LONG BC> and load the parameter set.

†

†

Select the <Brightness measurement value C1> parameter.

Automatic calibration

†

†

Set up the LMS MG PROGRAM REMOTE BT according to 

the drawing, and move a few steps away from the mea-

surement location, so the lux measurement will not be 

influenced.

†

†

Press OK.

 

A new window with the measured brightness measu-
rement value is shown. If you would like to apply this 
value,

†

†

Press OK.

†

†

Important

: Press the send button ( ). After this, the 

brightness measurement is calibrated.

Manuel calibration using the lux meter

†

†

Set up or align the lux meter according to the drawing, and 

read the lux value.

†

†

Press "Enter" in the app.

 

A new window opens. 

†

†

Enter the lux value and press OK.

 

The brightness measurement value appears in the 
display. 

†

†

Important

: Press the send button ( ). After this, the 

brightness measurement is calibrated.

 

The calculated room correction factor is adopted. The 
room correction factor can be checked via the <Room 
correction factor C1> parameter for monitoring purposes. 
The default value is 0.3.

Switch on dimming value C1

In switching mode and in the constant light control function, 

the lighting is switched on with the switch-on dimming value.

Value range (Glamox Sensor-app)

Switch on dimming value C1

30–100%

Configuration type C1

Value range (Glamox Sensor-app)

Fully automatic device: the lighting is switched on and off 

automatically (based on presence, absence and brightness).

auto

Semi-automatic device: the lighting must always be switched 

on manually. It is switched off automatically by the presence 

detector (based on absence or brightness)

auto

IR group address C1

This parameter is applied when using the LMS MG USER 

REMOTE or app remote control LMS MG PROGRAM REMOTE 

BT.

A group address can be assigned to lighting channel C1. The 

group addresses in the detector can be programmed with 

the LMS MG PROGRAM REMOTE BT/App or LMS MG USER 

REMOTE.

Value range

Adjustable values from LMS MG PROGRAM REMOTE BT

I, II, III

Adjustable values from LMS MG PROGRAM REMOTE BT/

App

I–VIII, all

Adjustable values from LMS MG USER REMOTE

I, II

With the LMS MG USER REMOTE, the group address can be 

assigned as follows:

Press the   and 

 buttons at the same time for at 

least 5 s

I

Press the   and 

 buttons at the same time for at 

least 5 s

II

With the app remote control, the group address can be assig-

ned without the app as follows:

Press the   and 

 buttons at the same time for at 

least 5 s

I

Press button A and the 

 button at the same time for 

at least 5 s

II

Press the   and 

 buttons at the same time for at 

least 5 s

III

Scene 1 C1/Scene 2 C1

The required dimming value for lighting channel C1 can be 

assigned to scene 1 and scene 2.

Value range (Glamox Sensor-app)

Adjustable values

0–100 %

Summary of Contents for B29004003
















Reviews: