9
•
The presence detector responds exactly as in normal
operating mode, only the reaction to brightness/dark-
ness is faster.
•
In order to simulate this behaviour, either the area below
the presence detector can be illuminated or the blinds
operated.
•
Test mode ends automatically after 10 min.
The detector restarts itself (see switch-on behaviour on
page 10).
L
Note: Do not use a torch to switch on the presence
detector! The adaptive light switching thresholds will be
distorted!
Factory settings
The presence detector is supplied with the following parame-
ter values:
Parameter
Value
Function C1/C2
Control
Function C3
Control
Light measurement source C3
centre
Terminal S1 assignment
C1
Terminal S2 assignment
C2
Terminal S3/P assignment
Parallel
Brightness set point value C1, C2, C3
500 lux
Room correction factor Win, Mid, Inn, Int
0.3
Detection sensitivity (PIR)
Increment 3
Lighting time delay
10 min
Short presence
On
Energy saving mode
eco
Switch-on dimming value C1, C2, C3
50 %
Configuration type C1/C2, C3
auto
Control speed
Standard
Minimum dimming value
10 %
Maximum dimming value
100 %
Switching off brightness
10 min
Response after dimming
school
Standby time
0 s
Standby dimming value
10 %
IR group address C1
I
IR group address C2
II
IR group address C3
III
Scene 1 C1, C2, C3
30 %
Scene 2 C1, C2, C3
70 %
Configuration button/RC
enabled
LED display motion
off
The parameters can only be set to factory settings by using
the app in combination with the app remote control.
Reset DALI ECGs
The connected DALI ECGs are reset to factory settings and the
group addresses are deleted.
9. Start-up
Initial operation (system not configured)
After first switching on the system power supply, the detector
is restarted, automatically identifies all connected DALI lamps,
assigns short addresses and manages them in a list. This
stage is indicated by an LED flashing pattern (5 x on briefly
every 3 s) and, depending on the size of the system, can last
up to 3 min.
If no DALI ECG is connected to the detector or a DALI line is
interrupted, the detector shows this with the LED flashing
pattern (LED is on and flashes off briefly twice every 3 s).
If the system is OK, the detector automatically enters con-
figuration mode and waits for configuration of the lighting
groups. This is indicated by the LED flashing pattern (2 x on
briefly every 3 s). If configuration has not been carried out the
system will be in the following operating mode:
•
Detector is in broadcast mode.
•
Function is switching mode (only presence detection, no
light measurement).
•
All lights are controlled with 100% switching/dimming
value.
•
The operating mode is as a fully automatic device.
•
All connected buttons are active. It is possible to switch
on and off, as well as dim.
•
Time delay 10 min.
Configuration of the lighting groups
For the configuration, there are two options available:
•
Using the
app in combination with the app remote
control
•
Using the buttons or user remote control
Configuration of the lighting groups by app remote control/
app
y
Connect the LMS MG PROGRAM REMOTE BT with the
Glamox Sensor-app.
y
Place the LMS MG PROGRAM REMOTE BT under the detec
-
tor (direct the remote control towards the detector).
y
Select type LMS MG PIR CLS SENSOR-R/QA in the app.
y
In the „DALI configuration“ menu, select the required group
assignment.
For the DALI configuration, there are 3 options available:
•
„Group assignment (unaddressed)“: Only DALI ECGs wit
-
hout a group address are processed.
•
„Group assignment (All)“: All connected DALI ECGs are
configured.
WARNING
: All existing group assignments
with group number 1, 2 or 3 will be deleted.
•
„Change group assignment“: The next available ECG will
be searched for and selected.
▻ After selecting the required group assignment, the
detector is in the programming mode.
▻
A DALI lamp starts to pulse (random order).
y
Select the desired channel C1, C2 or C3 and assign with
to the DALI ECG.
▻ The lamp confirms the assignment by dimming to
20 %.
▻ The next DALI lamp starts to pulse. In this way, all of the
lights are assigned to the lighting groups successively.
