4
Master
DALI
DA+ DA–
S1 S2
EVG
S3/P
N
L
N
L
EVG
Master/master parallel switching
Several masters can be used in parallel switching. Each
master controls its lighting groups according to its own
brightness measurements. Time delays and brightness
setpoint values are set individually on each master. Presence
continues to be detected by all detectors.
Master
DALI
DALI
DA+ DA–
S1 S2
S3/P
N
L
N
L
EVG
Master
DA+ DA–
S1 S2
S3/P
N
L
EVG
•
Master with 2 lighting groups and individual brightness
measurement
•
Switch up to 10 detectors in parallel
•
Use the same phase for all detectors and buttons
8. Settings
The presence detectors are supplied with basic settings ready
for operation. The specifications are guidance values. The app
remote control LMS MG PROGRAM REMOTE BT in combination
with the Glamox Sensor-app is available for start-up support.
They enable remote setting. The parameters can be queried,
adjusted and optimised. A range of variable parameters is
available for adjustment with the remote control (see section
“Parameters via remote control”).
Settings via the button
Pressing any button for longer than 15 s triggers the teach-in
of the brightness setpoint value by the teach-in function. In
addition, the teach-in function can be conveniently executed
via app in combination with the app remote control LMS MG
PROGRAM REMOTE BT (see section “Control commands via
remote control”, page 8).
The teach-in function via the button can be disabled using
the app when the <Configuration button/RC> parameter is
set to “disabled”.
The lighting groups can also be configured using the but
-
tons. All connected buttons can be used for configuration.
A detailed description can be found in chapter „9. Start-up“
(page 9).
Configuration via the buttons can be disabled via app in com
-
bination with the app remote control when the <Configuration
button/RC> parameter is set to “disabled”.
Parameters via remote control
The following parameters can be checked or changed via
the remote control for support during start-up as well as
servicing:
Parameter
Description
Can be
checked
via app
Can be
changed
via app
Function C1/C2
Function C3
Selection: switching/
control
x
x
Light measurement
source C3
Selection: Centre/
Integral
x
Terminal S1 assignment
Terminal S2 assignment
Selection: C1/C2/
C1+C2/C3/C1+C3/
C2+C3/C1+C2+C3
x
Terminal S3/P
assignment
Selection: Parallel/C1/
C2/C1+C2/C3/C1+C3/
C2+C3/C1+C2+C3
x
Brightness set point value
C1, C2, C3
Value range in lux/
measurement off
x
x
Brightness actual value
C1, C2, C3
Query brightness actual
value
x
Room correction factor
Win
Room correction factor
on side towards window
x
x
Brightness measurement
value Win
Lux meter brightness
value on side towards
window in lux
x
Room correction factor
Mid
Room correction factor
middle
x
x
Brightness measurement
value Mid
Lux meter brightness
value middle in lux
x
Room correction factor
Inn
Room correction factor
Inn
x
x
Brightness measurement
value Ins
Lux meter brightness
value interior in lux
x
Room correction factor Int Room correction factor
Integral
x
x
Brightness measurement
value Int
Lux meter brightness
value Integral in lux
x
Detection sensitivity (PIR)
Value range in
increments
x
x
Lighting time delay
Value range in seconds
and minutes
x
Short presence
Short-term presence:
On/Off
x
x
Energy saving mode
Selection: eco/eco plus
x
x
Switch-on dimming value
C1, C2, C3
Value range in %
x
Configuration type C1/C2
Configuration type C3
Selection: auto/man
x
x
Control speed
Selection: standard/
medium/fast
x
Minimum dimming value
Value range in %
x
Maximum dimming value
Value range in %
x
Switching off brightness
Value range in minutes/
hours/never off
x
Manual dimming
response
Selection: school/office
x
Standby time
Value range in seconds/
minutes/Permanently
on
x
Standby dimming value
Value range in %
x
IR group address C1,
IR group address C2,
IR group address C3
Selection: All/I/II/III
(App to VIII)
x
Scene 1 C1
Scene 2 C1
Scene for lighting chan-
nel C1 value range in %
x
Scene 1 C2
Scene 2 C2
Scene for lighting chan-
nel C2 value range in %
x
Scene 1 C3
Scene 2 C3
Scene for lighting chan-
nel C3 value range in %
x
