8
For IR group address C2:
Press the and
2
buttons at the same time for at least 5 s
I
Press button A and the
2
button at the same time for at least 5 s
II
Press the and
2
buttons at the same time for at least 5 s
III
Scene 1 C1, C2, C3/Scene 2 C1, C2, C3
The desired dimming value for each lighting group can be
allocated to scene 1 and scene 2.
Value range (Glamox Sensor-app)
Adjustable values
0–100 %
Using the user or app remote control, the lighting is firstly set
to a desired brightness and then saved as followed:
Press the button for at least 3 s.
Scene 1 is saved
Press the button for at least 3 s.
Scene 2 is saved
The scene is called up by briefly pressing the button.
Configuration button/RC
The teach-in function and the configuration of lighting groups
via the button or the remote controls can be enabled or disa-
bled with the <configuration button/RC> parameter.
Value range (Glamox Sensor-app)
Teach-in and configuration can be executed via the buttons/
remote controls.
Enabled
Teach-in and configuration via the buttons/remote controls id
disabled.
Disabled
LED display motion
The motion detection can be displayed via the LED.
Value range (Glamox Sensor-app)
No display of motion detection.
Off
The LED is switched on when motion is detected, otherwise it
remains off.
On
Control commands via remote control
The following control commands can be triggered with the
remote control:
Control command
Description
Can be
triggered
via app
DALI configuration
Configuration of the lighting groups
x
Group assignment
(Unaddressed)
Configuration of the unaddressed
lighting groups
x
Group assignment (All)
Configuration of all lighting groups
x
Change group
assignment
Change configuration of the lighting
groups
x
End group assignment
End configuration of the lighting groups
x
Reset DALI ECGs
All connected DALI ECGs are reset to
factory settings
x
Switching light C1
Lighting group C1 can be switched on
and off.
x
Switching light C2
Lighting group C2 can be switched on
and off.
x
Control command
Description
Can be
triggered
via app
Switching light C3
Lighting group C3 can be switched on
and off
x
Switching light (All)
All lighting groups can be switched on
and off together
x
Teach-in channel C1
Lighting channel C1 execution
x
Teach-in channel C2
Lighting channel C2 execution
x
Teach-in channel C3
Lighting channel C3 execution
x
Teach-in channel
C1 + C2 + C3
Activate for all lighting channels C1–C3
x
Presence test
On/Off
x
Light test
On/Off
x
Restart
Restart detector
x
Factory settings
Set all parameters and settings to fac-
tory setting; DALI configuration remains
unchanged.
x
Teach-in channel C1, C2, C3
During teach-in, the currently measured brightness value is
accepted as the brightness setpoint value. Values outside the
permitted range will automatically be set to the appropriate
limit value.
Value range (Glamox Sensor-app)
Teach-in channel C1
Teach-in for channel C1 Light
Teach-in channel C2
Teach-in for channel C2 Light
Teach-in channel C3
Teach-in for channel C3 Light
Teach-in channel C1 + C2 + C3
Teach-in for channel C1–C3 Light
Presence test
Presence test mode is used to test presence detection and
wiring. Presence test mode can be activated with the app in
combination with the app remote control. The detector goes
directly into test mode when the test mode is set:
•
Every movement is indicated by the LED.
•
When motion is detected, the lighting is switched on.
•
Constant light control is deactivated (switching mode).
•
Teach-in cannot be activated in test mode.
•
The lighting is switched off after 10 seconds when the
room is unoccupied.
•
Brightness measurement is deactivated, detector does
not respond to brightness.
•
Standby function is deactivated.
•
The detector reacts as in configuration type “fully auto
-
matic device”, even if “semi-automatic” is set.
•
Test mode ends automatically after 10 min. The detector
restarts itself (see switch-on behaviour on page 10).
Light test
The light test mode is used to check the brightness threshold
and the constant light control. The light test mode can be
activated with the app in combination with the app remote
control. The detector goes directly into test mode when the
test mode is set:
•
The LED shows the light test mode (5 seconds on, 0.3
seconds off).
