![background image](http://html.mh-extra.com/html/gima/49880/49880_manual_2227754007.webp)
19
ENGLISH
The room temperature rise or fall sharply, or the environment of measurement often changes;
Measuring in a moving vehicle;
The high and low location of cuff will cause changes in measurement results;
Continuous measurement for a long time.
7.2 Applying the Cuff
Both left and right arm can be measured.
Bare your arm or cloth close-fitting clothing during measurement.
Carry out the operation in a room with comfortable temperature.
When measuring, take the thick clothes off instead of rolling up the sleeves.
In order to measure accurately, pay attention to applying the cuff properly (left arm).
① Insert the arm cuff air plug in the cuff socket of sphygmomanometer
.
② Stretch cuff into a barrel for the arm can conformable enter into the barrel
③ Left arm penetrate through the cuff, the air tube of the cuff will pass the top of your palm.
④ Wrap the cuff to your upper arm. Make the air tube inside the forearm and aligned with your middle finger.
⑤ The bottom of the cuff should be approximately 2cm~3cm above your elbow.
⑥ Be fixed with cloths, and wrapped tight cuff, the arm and the cuff should not have gaps.
①
②
③
④
⑤
⑥
7.3 Measurement BP
①Under “OFF” state, press “START/STOP” button to start measuring.
During measurement, please keep correct pose and quiet state, the body could not move.The “Movement” icon appears if patient moves, and continue
measuring may lead to inaccurate measurement.
If you want to abort the measurement
Press
【
START/STOP
】
button,
t
he device will stop inflating,
and
release the air from the cuff
.
②Display the measurement results after finishing measuring.The pressure bar on the right side visually demonstrates the pressure level.
③Confirm the Measurement Value
The World Health Organization has established globally accepted standards for the assessment of high blood pressure readings.The SYS higher than
135mmHg or the DIA lower than 85mmHg are used as the criteria of hypertension, and the pressure bar at the right side lights up in red.
*Self-diagnosis and treatment using measured results may be dangerous. Follow the instructions of your physician.
Note
Wait at least 4-5 minutes between measurements.
When repeatedly measuring, the accurate blood pressure value may not be measured due to congestion in the arm
.
Please measure after the
blood flow is smooth.
When the screen displays Err, the measure can’t be carried out correctly.
Irregular pulse icon is displayed in the measurement results if the pulse internal is irregular during measuring, which may cause it is unable to take
measurement correctly. Please keep quiet and remeasure. If the irregular pulse icon appears frequently, please consult a doctor.
The minimum value of the patient’s physiological signal is the minimum limit that the device can measure. The device may obtain inaccurate
measurement results when it is operated below the minimum amplitude or minimum value of the patient’s physiological signal.
*The device will automatically turn off after five minutes in which there is no operation to the device, even if you forget to turn the power off.
CHAPTER 8 - MEMORY FUNCTION
The device can store NIBP values automatically, display up to 199 set of measurement results.
If 199 set of measurement data have been stored in current device, when saving the 200th set of data, the earliest set of data will be overwritten. If no
measurement values, the memory values can be not numerated.
Memory function can not be used during measuring.
When there is no measurement values, “
---
” will display on the review interface.
8.1 Review the Memory Value
1.Under “OFF” state, press “M” button to display the average value of the latest three set of data, when the number of measurement data is less than
three groups, it will supplement automatically. Continue to press “M” button in current interface to view all measurement records.
8.2 Delete Memory Values
1.Users can delete all memory values of the current user instead of separately delete one memory value
2.Under the memory interface, press “M” button and “START/STOP” button simultaneously for more than 5 s, after “DEL” appears on the screen, all
memory values will be deleted.
Caution
When querying the measurement records, please press “M” button continuously to query one by one.
CHAPTER 9 - KEY
A
ND SYMBOLS