background image

22

ENGLISH

appointed institutions, or by professional personnel or contact us for inspection. Under the setting interface, Press the “START/STOP” button once, 

after “CAL” appears on the screen, press “M” button for more than 15 s to enter the static pressure interface.

 Advice 

 

Do not use gasoline, volatile oil, diluent, etc. to wipe the device.

Do not clean or wet the cuff.

Storage:

 Advice 

Do not expose the device in direct sunlight for long time, otherwise the display screen maybe damaged.

The basic performance and safety of the device are not affected by the dust or cotton wool in home 

environment,while the device shall not be placed where with high temperature, humidity or dusty.

Aged cuff may result in inaccurate measurement, please replace the cuff periodically according to the user manual.

To avoid device damage, keep the device out the reach of children and pets.

Avoid the device close to extreme high temperature such as fireplace, otherwise the device performance may be affected.

Do not store the device with chemical medicine or corrosive gas.

Do not place the device where there is water.

Do not place the device where with slope, vibration or impact

Take the batteries out if the device is not to be used for three months or longer.

CHAPTER 13 - NIBP SPECIFICATION

Name

Electronic Sphygmomanometer

The degree of protection against ingress of water

IPX1

Display

LED

NIBP Specifications

Measurement Method

Oscillometric method

Working mode

Automatic

Operation mode

Continuous operation

Pressure Range

0~297 mmHg(0~39.6 kPa)

Measurement range

Pressure

SYS

30

270 mmHg(4

36 kPa)

DIA

10

220 mmHg(1.3

29.3 kPa)

Pulse: 40~240/min

Inflation

160±5 mmHg(21.33±0.67 kPa)

Overpressure protect

297±3 mmHg(39.6±0.4 kPa)

Resolution

Pressure: 1

 

mmHg(0.133 kPa)

Accuracy

Static pressure: ±3 mmHg(±0.4 kPa)

Error

The BP value measured by the device is equivalent with the measurement value of 

Stethoscopy, perform clinical verification in accordance with the requirements in ISO 

81060-2: 2013, whose error meets the followings:

Maximum mean error: ±5 mmHg

Maximum Standard deviation: 8 mmHg

Operating Temperature/ Humidity

+5ºC~40 ºC      .  15%RH~85%RH(no condensat

ion)

Transport

Transport by general vehicle or according to the order contract, avoid pounded, shake and 

splash by rain and snow in transportation.

Storage

Temperature: -20 ºC~+55 ºC; Relative humidity: ≤95

 

%; No corrosive gas

 and 

drafty

.

Atmospheric pressure

700 hPa~1060 hPa

Power supply

4 “AA” alkaline batteries, AC Adapter(AC, 100 V-240 V, opti

onal)

Rated current

≤ 600 mA

Battery life

When  the  temperature  is  23  ºC,  limb  circumference  is  270  mm,  the  measured  blood 

pressure is normal, 4 “AA” alkaline batteries cab be used about 300 times.

Main Unit Dimensions

129

*

101

*

72 mm

  

Main Unit Weight

281 gram(without batteries)

Safety classification

Class 

 equipment (power supplied by power adapter)/Internally powered equipment 

(power supplied by batteries)

Type BF applied part

Service life

The service life of the device is five years or 10000 times of BP measurement.

Date of manufacturer

See the label

Summary of Contents for 49880














Reviews: