GILES FSH-4 Hood Operation & Service Manual Download Page 7

Page: 7 / 68

Model: FSH-4 Hood

Safety

Safety Overview:

The information contained in this manual has been prepared to describe the proper procedures for safely installing,

operating and maintaining

Giles Food Service Equipment

Throughout the manual, safety precautions are identified by a hazard alert symbol and key words such as

DANGER

WARNING

CAUTION

. Alert information precedes the tasks to which it applies. Suggested, recommended, or

other noteworthy information is identified as

NOTES

, or will be noted as

IMPORTANT!

. Additionally, certain words

are used to indicate a specific meaning, or to add emphasis as follows:

Shall:

understood to be mandatory.

Should:

understood to be advisory.

May:

understood to be permissive.

Will:

indicates a future event or condition to occur.

Indicates an imminently hazardous situation which, if not avoided, will result in serious personal injury, even

death.

Indicates a potentially hazardous situation which, if not avoided, could result in serious injury, even death.

Indicates a potentially hazardous situation which, if not avoided, may result in minor to moderate injury. This

notification is also used as an alert to unsafe practices.

If used without the safety alert symbol, indicates a potentially hazardous situation which, if not avoided, may

result in equipment and/or property damage, and may void the factory warranty.

NOTE or IMPORTANT!

Identifies suggested, recommended, or other important information.

Hazard Alert Symbols

are used in conjunction with key words, such as

DANGER

WARNING

, or

CAUTION

to alert Users to potential personal injury hazards and/or poor operating practices. These will

immediately precede precautionary measures pertaining to avoiding such hazards or practices. Adhere to all

information following these symbols to avoid possible injury, or even death. Failure to do so may also void the

factory warranty.

This product can expose users to chemicals including lead, nickel, aluminum, brass, carbon, copper or BPA

which are known in the state of California to cause cancer, birth defects and other reproductive harm. For

more information go to:

www.p65warnings.ca.gov

Summary of Contents for FSH-4 Hood





































































Search results

Summary of Contents for FSH-4 Hood

Reviews:

Related manuals for FSH-4 Hood

Brands by name

Popular brands

GILES FSH-4 Hood, Operation & Service Manual

Search results

Summary of Contents for FSH-4 Hood

Reviews:

Related manuals for FSH-4 Hood

Brands by name

Popular brands