GILES FSH-4 Hood Operation & Service Manual Download Page 57

Page: 57 / 68

Model: FSH-4 Hood

Parts List

This section lists some of the various parts that are available for replacement on the unit. This is not an all inclusive

listing.

7.01

Parts Ordering & Service Information

Our goal at Giles is to provide the highest possible quality of service and assistance. To help us accomplish this,

please have the following information readily available when calling, along with a brief description of the problem

being experienced. Please record the unit information in the table below for quick reference.

The information can be found on a

serial/data label similar to this, located

on the hood side.

IN THE UNITED STATES & CANADA call:

800.554.4537

ALL OTHERS call:

334.272.1457

Normal business hours are 8:00 AM to 5:00 PM Central Time ... calls are handled by an auto-attendant answering

system. Please follow the recorded prompts to route your call appropriately. If necessary after hours, leave a

voicemail message and a representative should respond within 30 minutes.

Website:

www.gfse.com

Email:

[email protected]

Giles

is an equipment manufacturer and we do not sell parts direct. Parts for our equipment are available through

authorized service agents, part distributors, and/or kitchen equipment dealers. If assistance with sourcing parts or

equipment repair service is required, please contact a

GILES

Manufacturer’s Representative to assist with locating a

parts source or authorized service provider near you. For further assistance you may contact the

GILES

Technical/Customer Service Support

as follows:

Model:
Serial Number:
Voltage:
Phase:

Summary of Contents for FSH-4 Hood





































































Search results

Summary of Contents for FSH-4 Hood

Reviews:

Related manuals for FSH-4 Hood

Brands by name

Popular brands

GILES FSH-4 Hood, Operation & Service Manual

Search results

Summary of Contents for FSH-4 Hood

Reviews:

Related manuals for FSH-4 Hood

Brands by name

Popular brands