Giga-tronics 8650A Series, Operation Manual

Page: 87 / 240

Remote Operation
Manual 31470, Rev. E, April 2001 3-13
SENSe<sensor 1 or 2>:CORRection:OFFSet
[:MAGnitude]
space <offset value in dB -99.99 to 99.99>
Compensate sensor 2 for 10.2 dB attenuation
3-35
SENSe<sensor 1 or 2>:CORRection:OFFSet:STATe space <ON
or OFF>
Enable sensor 2 offset correction
3-35
SENSe<sensor 1 or
2>:CORRection:VPROpf[:STATe]
space <ON or OFF>
Enable sensor 1 v_prop_f function
3-25
SENSe<sensor 1 or 2>:TEMPerature? Query sensor 1 temperature (in centigrade)
3-15
SENSe<sensor 1 or 2>:TRIGger:SOURce space <peak sensor
triggering INTernal, EXTernal or CW>
Set sensor 1 peak trigger mode to CW mode
3-31
SENSe<sensor 1 or2>:TRIGger:DELay[:MAGnitude]: space
<Peak Sensor sample delay in seconds from -20e-9 to 104e-3> Set sensor 2 peak delay value to 1e6 seconds
3-31
SENSe<sensor 1 or 2>:TRIGger:DELay:STATe space <ON or
OFF>
Enable peak sensor 1 delay function 3-31
SENSe<sensor 1or2>:TRIGger:LEVel[:MAGnitude] space
<trigger level of peak power sensor>
Set peak sensor 1 trigger level to 1.7 volts
3-32
SENSe<sensor 1 or 2>:TRIGger:OFFSet[:MAGnitude] Set peak sensor 1 trigger offset time to 0
second
3-32
SENSe<sensor 1 or 2>:TRIGger:TOTAl[:MAGnitude]? Query peak sensor 1 total trigger delay time
3-32
*SRE space <event status register value, 128, 64, 32, 16, 8, 4, 2,
1>
Enable bit 5 of Status Byte register 3-36
STATus:OPERation[:ENABlet] Set Status Enable Mask TBA
STATus:OPERation[:EVENt]? Query operation event register result
3-37
STATus:PRESet Clears all the status register value
3-37
3-47
SYSTem:COMMunicate:GPIB Collect Configuration of Control Interface
TBA
SYSTem:COMMunicate:SERial:RECeive:BAUD space <baud
rate>
Set the receive baud rate TBA
SYSTem:COMMunicate:SERial:TRANsmit:BAUD space <baud
rate>
Set the transmit baud rate
TBA
SYSTem:ERRor? Query system error message
3-51
SYSTem:LANGuage NATIVE Switch to native language
TBA
SYSTem:PRESet Reset 8650A configuration 3-47
SYSTem:VERSion? Query SCPI version
3-49
TRIGger[:IMMediate] Trigger measurement cycle
3-19
TRIGger:SOURce space <instrument triggering source
IMMediateBUS, HOLD, or EXTernal>
Set instrument measurement trigger source to
IMMediate 3-19
TRIGger:MODE space <burst mode data gathering POST trigger
receipt or PRE trigger receipt>
Set Burst or Swift mode data collection relative
to Timing of event trigger post
3-20
TRIGger:DELay space <delay time between buffered readings in
sec 0.000 to 5.000>
Set Burst mode measurement time to 5 ms
between measurements (resolution, one msec)
3-20
TRIGger:COUNt space <number of data values to buffer in
memory from 1 to 5000 for standard 8650s from
1 to 128,000 on one channel with option 02; from
1 to 64000 for two channels with option 02> Set Burst or Swift mode buffer reading number
to 100
3-21
Table 3-3: SCPI Command Syntax (Continued)
Command Syntax Function Page