manualshive.com logo in svg

GHM HONSBERG OMNIPLUS-F Series, Operating Manual

Share
Download
GHM HONSBERG OMNIPLUS-F Series Operating Manual Download Page 27

 

 

OMNIPLUS-F 

Operation | 6 

C-E01_X__OMNIPLUS-F__DB2-1.0 

27/ 45 

6.5.9  Parameter "Start of range | End of range | 

Display value"  

 
Only visible and configurable if "Medium" was previously set to "User defined  
Is set.

 

These three parameters are used to adapt the instrument to liquids other than water. 
They are only visible if "Medium" has been set to "user defined". The factory adjust-
ment then has no function. With the help of the three parameters, a new characteristic 
curve can be defined. 

For the procedure for setting the parameters, see 

chapter 6.2.2.6 Medium setting.

 

Setting values: 

Start of range 

0 ... 1.0000 

End of range 

0 ... 1.0000 

Display value 

0 ... 100 %  

 

6.5.10  "Response time" parameter 

"Response time" defines the response time of the flow measurement. This is the time 
that elapses after a sudden change in the flow velocity until the display has ap-
proached the new value. 

 

Setting values: 0.1 ...  99.9 sec 

 

6.6  "Volume totalizer" submenu 

The OMNIPLUS-F has a volume totalizer that can add up the flowed volume depend-
ing on the flow velocity and the set pipe diameter. The flow measurement does not 
have to be displayed in a flow unit for this purpose. However, the correct setting of the 
pipe diameter is a prerequisite for a meaningful summation. 

If the volume counter is activated, it can be displayed in the measured value display of 
the main display by 

RING-TURN

 

together with the instantaneous value. 

At the same time, a switching signal can be output on pin 4. For this purpose, pin 4 
must be configured accordingly (see "Pin 4 settings"). 

6.6.1  "Totalizer" parameter 

Enable or disable the volume totalizer. 

Setting values: 

ON - activates the volume totalizer display 

OFF - turns off the volume totalizer (

the parameters described below will be not

 

displayed) 

 

 

Summary of Contents for HONSBERG OMNIPLUS-F Series














































Reviews:

No comments

Brands by name

Popular brands

Load more brands