manualshive.com logo in svg

GHM HONSBERG OMNIPLUS-F Series, Operating Manual

Share
Download
GHM HONSBERG OMNIPLUS-F Series Operating Manual Download Page 17

 

 

OMNIPLUS-F 

Operation | 6 

C-E01_X__OMNIPLUS-F__DB2-1.0 

17/ 45 

6.1.2 Explanation of commissioning 

The following describes how to put the product into operation. 

 

Prerequisite: the product is correctly installed - see chapter 5 Installation. 

Electrical connection is established  

 

 

 

  NOTE - Start  

 

The product is preset at the factory with a default setting. It is necessary to select and 
set parameters for the desired operation. The individual setting is made by the opera-
tor. 

 

 

Switch on your plant or apply the auxiliary voltage for the OMNIPLUS-F on. 
You will receive a display indication: 

 

1.  The "Flow reading with unit" display is used as the start display. 

displayed. 

 

2.  With a rotation of the multifunction ring by one position to the right 

"Ring  

right" 

the display for the flow and temperature reading appears   

 

3.  With a rotation of the multifunction ring by one position to the left "

Ring left

" 

The "

Pin States

" display appears with a status display of the existing pin 

status.

 

of outputs 

 

These three displays are 

main displays.

  Each main display takes you to a submenu 

with further parameters.  The operation is described in the following chapters.  

 

4.  another 

fourth main display 

"Flow reading and volume totalizer" will be with a 

RING TURN is 

only visible if the configurable volume counter  

"

Volume totalizer

" has previously been set to ON. See also the note 

under chapter 6.1.3 Menu structure   

 

 

Summary of Contents for HONSBERG OMNIPLUS-F Series














































Reviews:

No comments

Brands by name

Popular brands

Load more brands