manualshive.com logo in svg

GHM HONSBERG OMNIPLUS-F Series, Operating Manual

Share
Download
GHM HONSBERG OMNIPLUS-F Series Operating Manual Download Page 12

 

 

5 | Mounting 

OMNIPLUS-F 

12/ 45 

C-E01_X__OMNIPLUS-F__DB2-1.0 

5.2  Threaded probe  

 

- 

OMNIPLUS-F-008

 

- 

OMNIPLUS-F-015

 

Threaded sensors have an external thread as process connection, with which they are 
screwed into a T-piece or a welding socket of the pipeline. The sealing is done e.g. 
with PTFE tape or with liquid seal. Sealing with the aid of a flat gasket is generally not 
possible, as the correct alignment of the X-marking is not guaranteed when screwing 
in as far as it will go. 

Due to the relatively short lengths of the available threaded probes, the range of appli-
cation is limited to nominal diameters from about DN15 to DN50. 

The following variants are available: 

 
-  Male thread G1/2", length 29.6 mm (type OMNIPLUS-F-015HK029) 

 

-  Male thread G1/2", length 45 mm (type OMNIPLUS-F-015HK045)

 

 

-  External thread G1/4", length 28 mm (type OMNIPLUS-F-008HK028)

 

 

 

 

Summary of Contents for HONSBERG OMNIPLUS-F Series














































Reviews:

No comments

Brands by name

Popular brands

Load more brands