25
3.6) Bending procedure
(
Ref. to Fig. 6)
During the bending operation, keep your hands well away from the
moving ram. Risk of crushing.
The bending process must be activated using the bending tool’s control button.
Do not use the control button (1) on-board the pump!
Press the control button (13) on the tool and keep it pressed down until
the motor switches off automatically.
When the motor switches off, release the button (13).
The bending operation is considered finished when the motor switches
off automatically and the tool’s piston has returned to its starting position.
In case of emergency, it is possible immediately interrupt the bending
process at any moment during the cycle by releasing the button (13)
and the tool’s ram will return to its starting position.
The “ERROR” message on the display (along with an audible signal),
indicates that the pump has reached the maximum developed pressure
but it was not possible to obtain the bend angle set on the tool.
Check the correct setting of the bending tool.
At the end of the operation, before disconnecting the hose, check that the ram of the
attached tool is fully retracted.
NOTE: For work needs, it is possible to perform an expansion
cycle without disconnect the cable from the connector (9),
in this case
it is essential to change the operating mode
through the diplay
(Ref. to
§ 4.2
for further details).
RESET
SW:S1J41405
ERROR
001
30001
BATTERY
002
003
BATTERY
004
max.
BATTERY
BATTERY
min.
BHP1518
NR 17CW185
10
29990
BATTERY
max 90°
90°
RESET
SW:S1K16500
P
n
= 155 bar
P
= 0 bar
P
n
= 2248 psi
LED
ON
max 90°
60°
*
1
*
2
*
3
*
4
*
5
*
6
7
P
= 0 psi
BEEP
max 90°
90°
P
n
= 155 bar
OK
P
n
= 155 bar
P
p
= 157 bar
P
n
= 155 bar
P
= 0 bar
max 90°
-15°
P
p
= 105 bar
P = 0 bar
P
p
= 325 bar
P
p
= 547 bar
RESET
SW:S1J41405
LED
OFF
ERROR
001
30001
BATTERY
P
n
= 729 bar
002
003
BATTERY
004
LED
ON
LED
OFF
LED
ON
max.
BATTERY
BATTERY
min.
B68MP
NR 16AW125
10
-29990
BATTERY
max 90°
90°
OK
P
n
= 729 bar
P
p
= 731 bar
RESET
SW:S1J41405
P
n
= 729 bar
P
= 0 bar
P
n
= 10573 psi
LED
ON
LED
OFF
max 90°
60°
*
1
*
2
3
4
*
5
*
6
*
7
8
*
9
10
11
P
= 0 psi
P = 0 bar
P
= 0 bar
P
n
= 729 bar
P
= 0 bar
BEEP
BEEP
RESET
SW:S1J41405
ERROR
001
30001
BATTERY
002
003
BATTERY
004
max.
BATTERY
BATTERY
min.
BHP1518
NR 17CW185
10
29990
BATTERY
max 90°
90°
RESET
SW:S1K16500
P
n
= 155 bar
P
= 0 bar
P
n
= 2248 psi
LED
ON
max 90°
60°
*
1
*
2
*
3
*
4
*
5
*
6
7
P
= 0 psi
BEEP
max 90°
90°
P
n
= 155 bar
OK
P
n
= 155 bar
P
p
= 157 bar
P
n
= 155 bar
P
= 0 bar
max 90°
-15°
P
p
= 105 bar
P = 0 bar
To return in bending mode change another time the operating
mode on the display.
RESET
SW:S1J41405
ERROR
001
30001
BATTERY
002
003
BATTERY
004
max.
BATTERY
BATTERY
min.
BHP1518
NR 17CW185
10
29990
BATTERY
max 90°
90°
RESET
SW:S1K16500
P
n
= 155 bar
P
= 0 bar
P
n
= 2248 psi
LED
ON
max 90°
60°
*
1
*
2
*
3
*
4
*
5
*
6
7
P
= 0 psi
BEEP
max 90°
90°
P
n
= 155 bar
OK
P
n
= 155 bar
P
p
= 157 bar
P
n
= 155 bar
P
= 0 bar
max 90°
-15°
P
p
= 105 bar
P = 0 bar
RESET
SW:S1J41405
ERROR
001
30001
BATTERY
002
003
BATTERY
004
max.
BATTERY
BATTERY
min.
BHP1518
NR 17CW185
10
29990
BATTERY
max 90°
90°
RESET
SW:S1K16500
P
n
= 155 bar
P
= 0 bar
P
n
= 2248 psi
LED
ON
max 90°
60°
*
1
*
2
*
3
*
4
*
5
*
6
7
P
= 0 psi
BEEP
max 90°
90°
P
n
= 155 bar
OK
P
n
= 155 bar
P
p
= 157 bar
P
n
= 155 bar
P
= 0 bar
max 90°
-15°
P
p
= 105 bar
P = 0 bar
RESET
SW:S1J41405
ERROR
001
30001
BATTERY
002
003
BATTERY
004
max.
BATTERY
BATTERY
min.
BHP1518
NR 17CW185
10
29990
BATTERY
max 90°
90°
RESET
SW:S1K16500
P
n
= 155 bar
P
= 0 bar
P
n
= 2248 psi
LED
ON
max 90°
60°
*
1
*
2
*
3
*
4
*
5
*
6
7
P
= 0 psi
BEEP
max 90°
90°
P
n
= 155 bar
OK
P
n
= 155 bar
P
p
= 157 bar
P
n
= 155 bar
P
= 0 bar
max 90°
-15°
P
p
= 105 bar
P = 0 bar
9
ENGLISH
