Getac W130 Series Operator'S Manual Download

Page: 17 / 134

Getting the Computer Running

This section guides you through the procedures for getting the
computer ready for operation.

Unpacking

After unpacking the shipping carton, you should find these
standard items:

Notebook Computer

Accessories:

−

AC adapter (100~240 VAC, 50~60 Hz)

−

AC power cord

−

Driver CD

−

Docking Station (Optional), include CD-ROM/COMBO & FD

Drive

−

Car adapter (12~32 VDC)

−

(Optional)

−

External battery charger

−

(Optional)

−

This

Operation Manual

−

Touchscreen Pen (Optional)

−

3M High Performance Cloth (Optional)

Inspect all the items. If any item is damaged or missing, notify
your dealer immediately.

Keep the shipping carton and packing materials in case you need
to ship or store the computer in the future.

Connecting to AC Power

The computer operates either on the external AC power or internal
battery power. It is suggested that you use AC power when you
start up the computer for the first time.

CAUTION: Use only the AC adapter included with your computer. Using other AC

adapters may damage the computer.

Getting

Started

1-2

Summary of Contents for W130 Series







































































































































Search results

Summary of Contents for W130 Series

Reviews:

Related manuals for W130 Series

Brands by name

Popular brands

Getac W130 Series, Operator'S Manual

Search results

Summary of Contents for W130 Series

Reviews:

Related manuals for W130 Series

Brands by name

Popular brands