Getac W130 Series Operator'S Manual Download | Manualshive

Page: 93 / 134

background image

VGA Allows you to select high-resolution displays

with richer colors. It can drive CD displays as
well as CRT displays.

Audio Allows you to take full advantage of the audio
subsystem.

Modem The modem driver allows you to transmit
information over a standard telephone line
through RJ-11 port.

Speedstep Press the Speedstep button, the system will
auto install for Window 2000.

LAN/Wireless
LAN

Allows you to use the network function of the

              computer.

USB 2.0    Allows your system to connect to USB 2.0
                  devices.

DirectX 8.1 Allows you to take full advantage of the
multimedia applications.

Chipset Ensures the full function of the following drivers.
Install this main chipset driver installing the device drivers.

Touchscreen      Allows you to use your fingers as a pointing device on the
                          LCD screen ( refer to the next section for further
                          instructions).

DOCKING DRV    Click on the WIN2000/WINXP button to install

docking driver, the system will auto install USB To

COM Port.

Note:

W130 can support USB 1.1 and USB 2.0 350K CCD

Installing Software Drivers

6-4

«
...
91
92
93
94
95
...
»

Summary of Contents for W130 Series







































































































































Reviews:

No comments

Related manuals for W130 Series

Brand: IBM Pages: 208

BUNDLES S16 OPTICAL MOUSE WIRED

Brand: PORT DESIGNS Pages: 1

Fairies Magic JC262i1

Brand: LEXIBOOK Pages: 32

Brand: EUROCOM Pages: 90

TravelMate 2440 Series

Brand: Acer Pages: 91

TravelMate 2440 Series

Brand: Acer Pages: 90

V1020 - LifeBook - Core 2 Duo GHz

Brand: Fujitsu Pages: 168

Brand: TONGFANG Pages: 44

Brand: TONGFANG Pages: 44

Brand: Toshiba Pages: 4

U305-S7477 - Satellite - Core 2 Duo GHz

Brand: Toshiba Pages: 4

Brand: Toshiba Pages: 4

Brand: Toshiba Pages: 4

Brand: Toshiba Pages: 4

Brand: Toshiba Pages: 4

Brand: Toshiba Pages: 4

Brand: Toshiba Pages: 4

Brand: Toshiba Pages: 3

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands