manualshive.com logo in svg

Getac W130 Series, Operator'S Manual

Share
Download
Getac W130 Series Operator'S Manual Download Page 71

Connecting a Serial Device 

Your computer has a serial port for connecting a serial device such as 

a serial mouse or modem. 

Follow this procedure to connect a serial device: 

1. Make sure the “COM1 Port” item is set properly in the SCU program. 

(See “Advanced Menu” in Chapter 5 for information.) 

2. Make sure the computer is not turned on. 

3. Plug the device cable to the serial port on the computer. 

 

NOTE: When the computer is connected to the optional docking station, plug its cable to 

the serial port on the rear of the docking station instead of using the serial port of the 

computer. 

 

4. Turn on the computer. 

NOTE: Portable modems that derive power through the serial port cannot be used with the 

computer. Instead, use a modem that is powered by its own internal battery or external AC 

power. 

 

  Expanding Your Computer 

4-4 

Summary of Contents for W130 Series







































































































































Reviews:

No comments

Brands by name

Popular brands

Load more brands