Geolux GLX-RSS-2-300 WL User Manual Download Page 69

Page: 69 / 71

GLX-RSS-2-300 WL User Manual

GLX-RSS-2-300 WL Non-Contact Flow Meter

3. Check that the distance between the instrument and the water surface is

within the instrument’s operating range.

Use a tape measure or a similar tool to measure the distance between the

instrument’s antenna and the water surface. If the distance to the water surface is

greater than the instrument’s operational range, the instrument will not be able to

measure the distance and the water level.

4. Check that the distance between the instrument and the water surface is

within configured active zone.

Connect the instrument to the Geolux Instrument Configurator PC application

over RS-232 connection. Check the active zone parameters – if the distance to the

actual water surface is outside of the predefined active zone, the instrument will

not be able to report the correct distance. Modify the active zone parameters so

that the actual distance to the water surface is within the active zone.

Summary of Contents for GLX-RSS-2-300 WL







































































Search results

Summary of Contents for GLX-RSS-2-300 WL

Reviews:

Related manuals for GLX-RSS-2-300 WL

Brands by name

Popular brands

Geolux GLX-RSS-2-300 WL, User Manual

Search results

Summary of Contents for GLX-RSS-2-300 WL

Reviews:

Related manuals for GLX-RSS-2-300 WL

Brands by name

Popular brands