Geolux GLX-RSS-2-300 WL User Manual Download Page 51

Page: 51 / 71

GLX-RSS-2-300 WL User Manual

GLX-RSS-2-300 WL Non-Contact Flow Meter

Picture 8. Geolux Instrument Configurator – Data View

Clicking the

Settings

button enables the user to configure the flow meter or upgrade the device to

a newer firmware version. The device settings are divided into 3 groups:

Interfaces, Processing

and

Measurement.

By clicking the name of a specific group, all the settings which belong to that group can

be viewed and changed. The following settings are displayed:

Interfaces

Baud rate

RS-232 protocol

RS-485 protocol

Device ID

Modbus settings

Warm up time

4-20 mA output

4-20 mA min.

4-20 mA max.

Level 4-20 mA min.

Level 4-20 mA max.

Processing

Sensitivity level

SNR threshold

Filter length

Direction filter

Level filter type

Level filter length

IIR constant

Amplitude threshold

Peak detector type

Measurement

Discharge unit

Velocity unit

Level unit

PGA sensitivity

Velocity min.

Velocity max.

Level active zone min.

Level active zone max.

Level sensor hight

Power management

A detailed description (as described in chapter 5 of this user manual) of the selected setting appears

on the right side of the window when the user clicks on, or begins to change, a specific setting. When

a setting is changed, the

Set

button will appear next to the setting. By clicking the

Set

button, the user

confirms the change, and the new settings are saved.

Summary of Contents for GLX-RSS-2-300 WL







































































Search results

Summary of Contents for GLX-RSS-2-300 WL

Reviews:

Related manuals for GLX-RSS-2-300 WL

Brands by name

Popular brands

Geolux GLX-RSS-2-300 WL, User Manual

Search results

Summary of Contents for GLX-RSS-2-300 WL

Reviews:

Related manuals for GLX-RSS-2-300 WL

Brands by name

Popular brands