Geolux GLX-RSS-2-300 WL User Manual Download Page 16

Page: 16 / 71

GLX-RSS-2-300 WL User Manual

GLX-RSS-2-300 WL Non-Contact Flow Meter

Surface Velocity Radar Settings

Communication Interfaces Parameters

Baud rate

N bits per second

Band Rate

1 bit

Baud rate -

Configures the baud rate (bits per second) for serial communication on both RS-232

and RS-485 data lines. This setting controls how many bits are sent on the communication line in

one second. The available values are standardized. Using higher baud rates over longer lines may

introduce errors in transferred data. The default instrument baud rate is 9600 bps.

RS-232 and RS-485 protocol

0 0

$ABCD...

Protocol RS232 and RS485

RS-232 protocol

- Selects the communication protocol to be used for data communication on RS-

232 interface. The NMEA protocol is a GPS-like human readable messaging protocol where each

data packet contains a checksum for data integrity verification.

RS-485 protocol

- Selects the communication protocol to be used on RS-485 half-duplex interface.

HS protocol is a simple request-response protocol for the simplest applications. Modbus RTU

protocol is a standardized protocol which is commonly used in automation and instrumentation as

it provides all measurements with detailed diagnostics of device operation and the possibility to

change the instrument’s operating parameters.

Summary of Contents for GLX-RSS-2-300 WL







































































Search results

Summary of Contents for GLX-RSS-2-300 WL

Reviews:

Related manuals for GLX-RSS-2-300 WL

Brands by name

Popular brands

Geolux GLX-RSS-2-300 WL, User Manual

Search results

Summary of Contents for GLX-RSS-2-300 WL

Reviews:

Related manuals for GLX-RSS-2-300 WL

Brands by name

Popular brands