background image

SC-IP Configuration

Initializing the SC-IP for Configuration

3-2

SpectraComm IP Router Card 

076R200-000

Installation and Operation Manual

Issue 2

Commands entered with the proper syntax and all required parameters and arguments will take 
affect immediately. If required parameters or arguments are missing from the command string, 
you will be prompted for them individually. 

Abbreviated commands are accepted at the command prompt. 

For information on configuring IP and subnet mask addresses, refer to 

Appendix A, Application Guidelines 

.

Initializing the SC-IP for Configuration

1. Ensure your workstation is equipped with communication software (i.e., Hyperterminal) for 

making a VT-100 connection. Consult your PC’s operating system documentation for details. 

2. For initial configuration of a SC-IP, you must configure a VT100-compatible terminal for the 

following settings:

 9600,8,

N,1

3. Connect the terminal to the SC-IP

 CRAFT 

(console) port using the provided cable: 

(GDC P/N 029H211-001).

4. Make a Hyperterminal connection to the

 CRAFT 

port.

5. Hit <

CR

> a few times or press

 CTRL-R

. The following login screen will appear, followed by 

a command line prompt:

***************************************************************************
***************************************************************************
**                                                                       **
**         W E L C O M E   T O   S P E C T R A C O M M   I P             **
**                                                                       **
**                   Copyright General DataComm 2002                     **
**                                                                       **
**                     Running version is T0.0.18                        **
**                                                                       **
**          Use "?" at any time on the command line to get help.         **
***************************************************************************
***************************************************************************

                SC-IP>

Note

For online help screens describing all CLI options, press

 ? 

Note that the CLI options for configuring the 

SC-IP are only available when you have enabled supervisor privileges or the higher admin privileges.

6. Enable supervisor privileges by typing

 enable <cr>

When prompted for the password, type:

supervisor <cr> 

[default supervisor password]

7. The SC-IP is now operating in supervisor mode as shown by the

 # 

symbol in the new CLI 

prompt, with all CLI options available. 

8. You can now configure the SC-IP to suit your network by typing the required configurations 

commands at the CLI prompt. You do not need to set parameters that coincide with system 
defaults. Any configuration changes will take affect immediately.

Note

FOR ADVANCED USERS: The SC-IP provides a utility for generating the configuration settings of a SC-IP 
into an ASCII file, simplifying the configuration of multiple SC-IPs. This function can also be used to archive 
configuration data for specific unit or as a baseline for modified configurations.
Refer to 

Appendix A, Application Guidelines 

Batch Up/Download Overview 

.  

Summary of Contents for SC-IP



























































































Reviews: