manualshive.com logo in svg

General Air Products NGP-1000D-M2, Installation, Operation And Maintenance Manual, Page: 20 / 34

Share
Download
General Air Products NGP-1000D-M2 Installation, Operation And Maintenance Manual Download Page 20

1-800-345-8207

20

Section 10 - Nitrogen Generator Alarms/Troubleshooting

The nitrogen generator has 7 alarms. If an alarm is activated, the alarm light will turn red on the outside of the cabinet and

the Alarm Horn will sound. The alarm number will also display on the Nitrogen Control Module inside the cabinet.

To clear alarms, cycle power or press ALT then hold the

right arrow key for 5 seconds. Press ALT again to get

back to main menu. There is also a silence button on the

back of the Alarm Horn.

Alarm 1 – Nitrogen Solenoid Excess Cycles

Issue:

The nitrogen solenoid has cycled more than 36 times in 12 hours.

NOTE:

More than 8 cycles a day will reduce membrane life below 10 years.

Answer:

1.

If the nitrogen solenoid is ON, check the pressure on the nitrogen storage tank. It should be below 80 PSI. If the 

pressure is greater than 80 PSI, the pressure switch may need re-adjustment or replacement.

2.

Check the nitrogen generator system for leaks.

3.

Check the sprinkler system for leaks.

Alarm 2 – Bypass Alarm

Issue:

The nitrogen generator has been left in Bypass Mode (Air Fill) for over 1 hour. This alarm clears when the unit has

been placed in Nitrogen Mode. It is designed to prevent the unit from being inadvertently left in Bypass Mode.

Answer:

1.

Turn the Bypass Valve (Yellow Handle) to the OFF position. Open the Nitrogen "Inlet" Valve (Blue Handle) and the

Nitrogen "Outlet" Valve (Blue Handle). Refer to Nitrogen Filling Procedure.

2.

If the unit is filling multiple systems, or being left intentionally in Bypass Mode, mute the Alarm Horn by pressing 

the button on the inside of the cabinet on the back of the Alarm Horn.

Alarm 3 – Compressor Overload

Issue:

The control panel has tripped due to a motor overload.

Answer:

1.

Turn power OFF to the nitrogen generator.

2.

Check overload setting.

3.

Reset the thermal overload located at the bottom of the compressor contactor. Measure amperage of motor - 

check for excessive amp draw.

Alarm 4 – Excessive Air Compressor Run

Issue:

The air compressor has run for longer than 45 minutes continuously.

Answer:

1. 

Check the pressure in the air storage tank. If the pressure is greater than 105 PSI and the compressor is still

running it could indicate a pressure switch issue.

2.

Check the nitrogen generator system for leaks.

Alarm 5 – Compressor Fail To Start

Issue:

Contactor auxiliary contacts did not close.

Answer:

1. 

Troubleshoot contactor wiring and functionality. See alarm 4.

2. 

Replace contactor.

Summary of Contents for NGP-1000D-M2



































Reviews:

No comments