Gemini iTRAX BLACK Operation Manual Download Page 5

Page: 5 / 19

3 BAND EQUALIZER

: The

3 BAND EQUALIZER

adjust the tone of

each

CHANNEL

by giving you a choice 3 frequencies (

BANDS

) to

adjust , from

LOW

MIDRANGE

(

MID

) and

HIGH

’s, you can use the

adjustment knobs to higher or lower the 3 separate frequencies till
the sound of the music program is appropriate for your listening
environment.

VU METER:

The

iTRAX

has a

VU METER

that allows you to moni-

tor the decibel levels of the

LEFT

and

RIGHT MASTER

output.

CHANNEL VOLUME FADER

: After you have chosen which input

you will use with the

INPUT SELECTOR

the corresponding

CHAN-

NEL FADER

will allow you to adjust the volume for that particular

CHANNEL

CROSSFADER

: The

CROSSFADER

allows you to mix evenly from

one source to another. The

CROSS FADER

on the

iTRAX

is also re-

movable and if the need arises can be replaced.The RG-45 (RAIL-
GLIDE™)

DUAL-RAIL CROSS FADER,

which has internal dual

stainless steel rails that allow the slider to ride smoothly and accu-
rately from end to end can be purchased from your local

GEMINI

dealer.

1/4” MIC INPUT

: This input is found on the face of the mixer, and is

used for connecting microphones that are terminated with a 1/4”
connector. This input is controlled solely by the volume and EQ con-
trols found directly to the right of the jack.

MICROPHONE VOLUME

: Allows you to adjust the volume of the mi-

crophone signal.

MICROPHONE EQ

: The

MICROPHONE EQ

Let’s you to control the

low frequency and the high frequency of the microphone signal.

CHANNEL CUE SELECTOR:

The

CHANNEL CUE SELECTOR

al-

lows you to choose which channel you wish to monitor in your head-
phones.

CUE VOLUME ROTARY KNOB:

The

CUE VOLUME ROTARY

KNOB

adjusts your

HEADPHONE MONITOR OUTPUT’S

volume.

HEADPHONE OUTPUT

: The

HEADPHONE OUTPUT

located at the

front of the

iTRAX

will accept any headphone with a standard 1/4”

connector and or adapter and will allow you to

CUE

your music pro-

gram before you play it.

iTrax BLACK

FADER REPLACEMENT:

CONTROLS:

Remove the screws on the bottom of the

unit using the appropriate sized screwdriver.

Remove the

CUE SELECTION FADER

knob, simply by firmly pulling the knob off.

Remove the back cover of the mixer, and

dislodge the printed circuit board which
houses the

X-FADER

, along with the 1/4” Mic

Input, Mic Volume, Mic On/Off Indicator LED,
Mic EQ Controls, and Cue Section.

Remove the screws on the left and right-

hand side of the

X-FADER

and remove the

plug from the bottom of the fader assembly.
The fader can now be removed completely.

Taking care to replace the fader in the cor-

rect direction, simply reconnect the plug to the
bottom of the fader assembly and secure the
fader by replacing the screws. Seat the printed
circuit board carefully back to where it was
originally installed.

Carefully replace the back cover, and

replace the screws. Be sure not to overtighten
the screws. If the unit does not close properly,
examine the seating of the circuit board which
houses the

X-FADER

assembly..

SPECIFICATIONS:

Inputs:

Phono...........................................................................3 mV, 47 KOhm
Line..........................................................................150 mV, 27 KOhm
MIC............................................................1.5 mV, 1 K Ohm Balanced
MIC High....................................................................................± 12dB
MIC Low.....................................................................................± 12dB
USB Input........................................................USB 2.0/1.1/1.0 B-Type

Outputs:

Master RCA.............................................................0 dB 1V, 400 Ohm
Max..........................................................................20V Peak-to-Peak
Record.......................................................................225 mV, 5 KOhm

General:

Frequency Response........................................20Hz - 20KHz +/- 2 dB
Distortion..................................................................................< 0.02%
S/N Ratio..................................................................Better Than 80 dB
Headphone Impedance............................................................16 Ohm
Power Source....................................Adapter 115v 60Hz/15v AC 1.5A
..........................................................Adapter 230v 50Hz/15v AC 1.5A

WEIGHTS AND DIMENSIONS:

Dimensions: 12.5 x 4.2 x 14” (318 x 107 x 356 mm)
Unit Weight: 12 lbs (5.44 kg)

SPECIFICATIONS SUBJECT TO CHANGE WITHOUT NOTIFICATION

FOR IMPROVEMENT